GE Infinity M Series Скачать руководство пользователя страница 75

Страница: 75 / 90

NE-M Installation Guide

H5692448

850050111

Issue 03 August 2017

Pulsar Controller Status

Display

Millennium Controller

Status Display

Rect/
Conv

LEDs

Dist.

Module

LED

Possible Problem(s)

Possible Solution(s)

MIN Thermal Probe
Fail

Norm
green

green

Battery thermal probe failed.

1. Ensure thermal probe is properly connected to thermal probe

cable.

2. Ensure cable is properly connected to the rear of the

Distribution Module.

3. If problem persists, replace thermal probe.
4. If problem persists, call your local field representative.

No response

Fail

red

blink

red

blink

Controller failure, all devices on the
communication bus reporting loss
of communication with controller.

1. Check controller to ensure it is properly inserted into its slot. If

so, perform the following steps:

2. Remove the controller input power connector for 1 minute and

then reset.

3. If problem persists, replace controller with new controller

board.

4. If problem persists, call your local field representative.

MIN Minor
Communication Fail

Fail

red

blink

(one

Unit)

green

Rectifier lost communication with
controller.

1. Reset the rectifier by removing the rectifier, waiting

approximately 30 seconds, and replacing.

2. If problem persists, replace the rectifier.
3. If problem persists, call your local field representative.

Norm
green

green

Rectifier removed from a running
system, but not uninstalled.

Issue the

Menu > Control / Operations > Uninstall Equipment

command for any rectifier that was removed.

green green green

BD AC DC

-54.48V1 1000A

FLOAT

Display Amber

Minor

Battery

amber

Display blank

off off off

BD AC DC

Display blank

green green green

BD AC DC

-54.48V1 1000A

FLOAT

Display Amber

Minor

amber

Содержание Infinity M Series



























































































Результаты поиска

Содержание Infinity M Series

Отзывы:

Похожие инструкции для Infinity M Series

Бренды по названию

Популярные бренды

GE Infinity M Series, Руководство по установке

Результаты поиска

Содержание Infinity M Series

Отзывы:

Похожие инструкции для Infinity M Series

Бренды по названию

Популярные бренды