background image

GEH-1768 

The  Type  IAV54F  relay  is  s imilar  to  the  Type  IAVS4E  relay,  except  that  it  has  a 

longer  operating  time. 

The  time  characteris tics  are  s hown  in  Figure  3. 

The  Type  IAV54H  relay  is  als o  s imilar  to  the  Type  IAV54F  relay,  except  that  it 

has  a  much  longer  operating  time  than  either  the  Type  IAV54E  or  the  Type  IAV54F 

relays . 

The  time  characteris tics  are  s hown  in  Figure  4. 

The  Type  IAVS5C  relay  is  s imilar  to  the  Type  IAV54E  relay,  except  that  it  has 

two  circuit-clos ing  contacts . 

The  Type  IAV55F  relay  is  s imilar  to  the  Type  IAV54F  relay,  except  that  it  has 

two  circuit-clos ing  contacts . 

The  Type  IAV55H  relay  is  s imilar  to  the  Type  IAV54H  relay,  except  that  it  has 

two  circuit-clos ing  contacts . 

The  Type  IAV55J  relay  is  s imilar  to  the  Type  IAV55H  relay,  except  that  it  is 

provided  with  two  s eparate  s eal-in  units ;  one  for  each  s et  of  normally-clos ed 
contacts . 

RATINGS 

The  operating-circuit  ratings  available  are  115,  230  or  460  volts  at  60,  50,  or 

25  cycles . 

The  operating  coil  will  s tand  rated  voltage  continuous ly  on  any  tap  and 

will  s tand  tap  voltage  continuous ly  on  the  taps  above  rated  voltage. 

The  current-clos ing  rating  of  the  contacts  1.s  30  amperes  for  voltages  not 

exceeding  250  volts . 

The  current-carrying  ratings  are  affected  by  the  s election  of 

the  tap  on  the  s eal-in  coil,  as  indicated  in  the  Table  1: 

Function 

Tripping  Duty 

Carry  Continuous ly 

TABLE  1 

AC  or  DC 

0. 2 

30 

0. 3 

The  2  ampere  tap  has  a  DC  resis tance  of  0. 13  ohms  and  a  60  cycle  impedance  of 

0. 53  ohms ;  the  0. 2  ampere  tap  has  a  7  ohm  DC  res is tance  and  52  ohm  60  cycle 
impedance. 

The  tap  setting  us ed  on  the  s eal-in  element  is  determined  by  the  current 

drawn  by  the  trip  coil. 

The  0. 2  ampere  tap  is  for  us e  with  trip  coils  that  operate  on  currents  rang1ng 

from  0. 2  up  to  2. 0  amperes  at  the  minimum  control  voltage. 

If  this  tap  is  us ed  with 

trip  coils  requiring  more  than  2  amperes ,  there  is  a  poss ibility  that  the  7  ohm 
res is tance  will  reduce  the  current  to  s o   low  a  value  that  the  breaker  will  not  be 
tripped. 

www 

. ElectricalPartManuals 

. com 

Содержание IAV54E

































Отзывы: