GE GTRC0 Series Скачать руководство пользователя страница 56

Страница: 56 / 63

– 42 –

Fresh Food Warm - Freezer Warm

Basic refrigeration checks:

Door gasket seal OK?

Door switch - light turning off with

door closed?

All OK?

Repair as

necessary.

YES

Reset electronics by unplugging

refrigerator for 15 seconds then

plug back in.

Is the evaporator fan running?

Go to Evaporator

Fan Not Running

flowchart.

YES

Is the condenser fan running?

Go to Condenser Fan

Not Running flowchart.

YES

Is the compressor running?

Go to Compressor Not Running

flowchart.

YES

Is the airflow in the fresh food

compartment normal?

Look for blockage

at vents or heavy

frost on evaporator

cover.

Blockage

Remove blockage from

evaporator cover vent

area.

YES

Verify thermistors are within

proper range.

Is the resistance within range?

Check wiring

connections. If OK,
replace thermistor.

Heavy frost

Go to Heavy Frost

on Evaporator

Cover flowchart.

YES

Check sealed system.

Does sealed system check

OK?

YES

Unit tests OK.

Run checks again. Look

for usage problem.

Содержание GTRC0 Series
































































Результаты поиска

Содержание GTRC0 Series

Отзывы:

Похожие инструкции для GTRC0 Series

Бренды по названию

Популярные бренды

GE GTRC0 Series, Техническое обслуживание руководство

Результаты поиска

Содержание GTRC0 Series

Отзывы:

Похожие инструкции для GTRC0 Series

Бренды по названию

Популярные бренды