GE GTRC0 Series Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 63

background image

– 30 –

Defrost Heater

The defrost heater is a single-tube, radiant
heater. It is held in place by 2 tabs on the
evaporator (1 on each side) and by 2 ceramic
and wire supports.

The ceramic and wire supports prevent the
heater from sagging and touching the metal
drain pan if the glass is broken.

Heater Supports

Defrost Drain Probe

Evaporator Thermistor

The evaporator thermistor is mounted on the
upper right side of the evaporator. The defrost
cycle will terminate when the main control board
detects 65°F from the evaporator thermistor.

The main control board must sense 65°F in less
than 45 minutes, or the defrost cycle will time
out. Normal defrost time is 25 minutes or less,
not including the 5-minute dwell or post dwell
periods.

Defrost Overtemperature Thermostat

The defrost overtemperature thermostat
(bimetal switch) is mounted on the evaporator
and provides overtemperature protection during
defrost. This thermostat will open at 140°F and
will close at 110°F.

Note:

The main control board will not know if

the heater does not come on due to a broken
heater, open defrost overtemperature
thermostat, or an open wiring harness. The
defrost heater is controlled by maximum time on
the main control board or temperature at the
evaporator thermistor.

Defrost Heater Supports

Defrost Overtemperature Thermostat

Evaporator Thermistor

«
...
42
43
44
45
46
...
»

Содержание GTRC0 Series
































































Отзывы:

Нет отзывов

Похожие инструкции для GTRC0 Series

Cafe CFCP1NIYSS

Бренд: GE Страницы: 2

Bottom-Freezer Built-In Refrigerator

Бренд: GE Страницы: 20

Бренд: F.Bertazzoni Страницы: 50

Бренд: Hoover Страницы: 325

Бренд: Dacor Страницы: 48

Бренд: White-Westinghouse Страницы: 32

Бренд: H&K Страницы: 22

Бренд: VOX electronics Страницы: 186

Бренд: Maytag Страницы: 24

Бренд: EAS Electric Страницы: 90

Бренд: Iceking Страницы: 20

Бренд: Fagor Страницы: 100

Бренд: Maytag Страницы: 56

Бренд: Arneg Страницы: 164

Бренд: Kenmore Страницы: 48

Бренд: Gaggenau Страницы: 817

Бренд: Vestfrost Страницы: 56

Бренд: Vestfrost Страницы: 88

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды