GE GCG200NGWC Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 58

background image

1. Summary of Heavy Repair

COOLING CYCLE HEAVY REPAIR

Installation should be conducted in accordance with
the standard installation procedure. (Leave space of
more than 5 cm from the wall for compressor
compartment cooling fan mounted model.)

Transportation
and
installation

Copper brush, Rag, Tool box

Remove flux from the silver weld joints with soft
brusher wet rag. (Flux may be the cause of corrosion
and leaks.)
Clean tools and store them in a clean tool box
or in their place.

Compressor
compartment
and tools
arrangement

Electronic Leak Detector,
Driver.

Check leak at weld joints.
Note :Do not use soapy water for check.
Check cooling capacity
- Check condenser manually to see if warm.
- Check hot pipe manually to see if warm.
- Check frost formation on the whole surface of the
evaporator.

Check
refrigerant leak
and cooling
capacity

Bombe (mass cylinder),
refrigerant manifold gauge,
electronic scales, punching
off flier, gas welding machine

Weigh and control the bombe in a vacuum conditions
with electronic scales and charge through compressor
inlet (Process tube).
Charge while refrigerator operates).
Weld carefully after inlet pinching.

Refrigerant
charging and
charging
inlet welding

Vacuum pump
, Manifold gauge.

Evacuate for more than forty minutes after connecting
manifold gauge hose and vacuum pump to high (drier)
and low (compressor) pressure sides.

Vacuum

Pipe Cutter, Gas welder,
N2 gas

Confirm refrigerant (R-134a or R-600a) and oil for
compressor and drier.
Confirm N2 sealing and packing conditions before use.
Use good one for welding and assembly.
Weld under nitrogen gas atmosphere.
Repair in a clean and dry place.

Parts
replacement
and welding

Nipper, side cutters

Cut charging pipe ends (Comp. & Dryer) and
discharge refrigerant from drier and compressor.

Remove
refrigerant
Residuals

Tools

Contents

Process

45

«
...
44
45
46
47
48
...
»

Содержание GCG200NGWC



























































Отзывы:

Нет отзывов

Похожие инструкции для GCG200NGWC

CoolMatic CRX50

Бренд: Waeco Страницы: 380

Бренд: Waeco Страницы: 300

Бренд: Gaggenau Страницы: 72

Бренд: Samsung Страницы: 260

Бренд: Concept2 Страницы: 84

Бренд: NEFF Страницы: 32

Бренд: Scandomestic Страницы: 23

Бренд: Igloo Страницы: 15

Бренд: Changhong Electric Страницы: 10

Бренд: Galanz Страницы: 6

Бренд: Bauknecht Страницы: 10

Бренд: mabe Страницы: 37

Бренд: VOX electronics Страницы: 112

Бренд: Haier Страницы: 24

Бренд: Haier Страницы: 29

Бренд: Haier Страницы: 10

Бренд: Haier Страницы: 29

Бренд: Haier Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды