1
Enter
Special Features
mode. See
To Enter Special
Features
section above.
2
Remove all articles from the washer basket.
3
Press the
Extra Rinse
button.
The
My Settings
and lights will go out. The
Start
button light will blink. The corresponding
Tank Levels
lights will show the current tank level.
4
Press the
Start
button.
The tank will dispense for the minutes shown in the
display to empty the selected tank. The
Tank Levels
lights will cycle 0,1,2,3,4,5,4,3,2,1,0 until the flush is
finished.
Once finished, the
Tank Level
will indicate an empty tank
(a single blinking red LED light) and the
Start
button will
be lit. You can (repeatedly) refill the tank with water and
press the
Start
button to rinse out the tank as needed.
NOTE:
If you suspect that the dispenser is plugged, add
lemon juice to make the water slightly acidic.
5
Press the
Power
button to exit (when the tank is
empty).
This function will automatically exit if neither button is
pressed for 2 hours.
NOTE:
Bulk tank flush is recommended if you:
1)
Change detergent or softener brands
2)
Accidently add softener to the detergent tank or
vice versa
3)
Put powdered detergent in the detergent tank
4)
Put non-concentrated fabric softener in the
softener tank
10
About special features.
To Enter Special Features
To enter the bulk tank
Special Features Mode
:
1
Press the
Power
button.
2
Simultaneously press and hold either the
Detergent Tank On
and
Detergent Cup Amount
buttons
for 3 seconds
or
Softener Tank On
and
Softener Cup Amount
buttons for
3 seconds
The
My Settings
and
Extra Rinse
lights will flash to
indicate you are in the
Special Features Mode
.
OR
Option 1: Set Concentration Settings
NOTE:
During initial installation, or if the household
water pressure dramatically changes, the bulk
dispenser will change to accommodate your homes’
unique water pressure. Wait a few wash cycles before
changing concentrations.
The factory default concentration settings are 1.5 oz
(44 ml) for detergent and 1.0 oz (30 ml) for softener.
To allow maximum user flexibility either of these can
be changed to between 0.5 and 10 ounces.
1
Enter
Special Features
mode. See
To Enter Special
Features
section above.
2
Press the
My Settings
button.
The
My Settings
and the chosen (Detergent
or
Softener)
3
Cup Amount
lights will come on and the
Extra Rinse
light will go out. The display will show “10 times in ounces”
the current concentration setting (e.g. 15 represents 1.5
ounces). This amount will be dispensed when 2 (of the 3)
Cup Amount
lights are lit.
3
Turn the cycle knob clockwise to increase or
counter-clockwise to decrease the setting (within
preset limits). Each click increases or decreases Level
2 (standard amount) by 1/2 ounce. Levels 1 & 3
change proportionally.
4
Press the
Cup Amount
button to save the new
setting.
This function will then exit and the display will reflect
whatever cycle the cycle knob is on.
To exit without changing the setting,
press the
Power
button. This function will automatically exit (without
saving) if neither button is pressed within 1 minute.
Option 2: SmartDispense
TM
Tank Cleaning
The following table shows the approximate amount dispensed (oz) at each
Cup Amount
setting (1, 2 or 3) for each
Concentration Setting
:
Concentration
Setting
5
10
15 20 25 30 35 40 45 50 55 60 65 70 75
80
85
90
95
100
200 100 67 50 40 33 29 25 22 20 18 17 15 14 13
13
12
11
11
10
0.6
1.3 1.9 2.5 3.1 3.8 4.4 5.0 5.6 6.3 6.9 7.5 8.1 8.8 9.4 10.0 10.6 11.3 11.9 12.5
0.5
1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 7.0 7.5
8.0
8.5
9.0
9.5
10.0
0.4
0.8 1.1 1.5 1.9 2.3 2.6 3.0 3.4 3.8 4.1 4.5 4.9 5.3 5.6
6.0
6.4
6.8
7.1
7.5
Number of
Loads*
*
For a 100 oz (2957 ml) bottle for normal ( ) setting.
