GE Dash Responder Скачать руководство пользователя | Manualshive

Страница: 16 / 100

background image

GE Medical Systems
Information Technologies

Servicing Manual Dash Responder V1.0

Revision F

Page 16 of 72

2004768-001

Indication of short-circuit

LED

what it means

comment

short-circuit in the device

disconnect battery from device

short-circuit of battery cells

battery defect, battery cannot be used any more

Fault indication

LED

what it means

comment

electronics fault

perform reset; if problem persists, battery
cannot be used any more

Perform reset

Test

> 10 s

For a reset, the TEST button needs to be pressed longer than 10 seconds. It is
recommended to perform a reset each time a fault is indicated. If the fault indication
persists, the battery is defective and cannot be used any more.

Automatic shut-down of the display (protection from deep discharging)

To protect the battery from deep discharging, the display shuts down automatically. The imminent
shut-down is indicated by running lights, with each of the 5 LEDs blinking in sequence for about 1
second. The display reactivates automatically when the battery is being charged.

Battery conditioning

The battery should be conditioned with the internal battery conditioning program or with the optional
battery charging unit ASU 3000 every month. As the ASU 3000 is a specially designed battery
charging unit that has a definite conditioning mechanism, it is advisable to use it to condition the
battery. Furthermore the conditioning cycle will last about twenty-one hours if performed in the
defibrillator and only five hours in the ASU 3000.

N

OTE

Since the battery will be discharged in the course of the program and the program takes several hours to
complete, a second charged battery must be available to ensure that the defibrillator is ready for use.

The conditioning program can only be run when the defibrillator is connected to the patient monitor
and the monitor, in turn, is connected to the power line.

Start of Conditioning

•

Connect the monitor-defibrillator system to the power line.

•

Turn the defibrillator on.

«
...
14
15
16
17
18
...
»

Содержание Dash Responder





































































































Отзывы:

Нет отзывов

Похожие инструкции для Dash Responder

Бренд: Tascam Страницы: 8

Бренд: B-K lighting Страницы: 5

Бренд: B-K lighting Страницы: 4

Бренд: B-K lighting Страницы: 3

Бренд: Garmin Страницы: 20

Бренд: Gaspardo Страницы: 16

Бренд: Gastrodomus Страницы: 4

Бренд: HANYOUNG NUX Страницы: 2

Бренд: Gastrodomus Страницы: 39

Бренд: OceanSat Страницы: 85

SimMan 3G Trauma

Бренд: laerdal Страницы: 16

Бренд: laerdal Страницы: 16

Бренд: laerdal Страницы: 60

Бренд: laerdal Страницы: 4

Resusci Anne Simulator

Бренд: laerdal Страницы: 8

Nursing Baby VitalSim

Бренд: laerdal Страницы: 15

Бренд: Cannon Страницы: 70

Бренд: Sakai Страницы: 31

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды