GE CyberDome II Скачать руководство пользователя страница 52

Страница: 52 / 60

CyberDome II

User Manual

Troubleshooting

This section provides information to help you diagnose and solve various problems that may arise while
configuring or using your GE product and offers technical support contacts in case you need assistance.

Common issues

The following are the most common troubleshooting issues and their solutions:

• The camera is displaying abnormal behavior. I have some control of the unit, but the camera is acting

strangely.

You can perform a restart from the controlling device, as long as you have control. To do the restart, do the
following:

1. Switch the keypad to the camera site you wish to reset.

2. Press and hold the

set

button until

Enter programming code

appears.

3. Press

and

seq

on the keypad.

4. You will see

Reset to Defaults

appear in the keypad window. Press

iris +

to proceed.

Note:

Despite the term

Reset to defaults

, this action does not reset any settings on the camera. It will only restart the

camera, as if you had cycled the power at the camera.

5. Press 3 for camera.

6. You will see

Reset camera X

Are you sure?

where X refers to the camera that the keypad was set to

before entering the 1, 4, 7, 6 and seq menu. Press iris + to proceed.

The camera will reset. If problems persist, check the data communication lines and power to the camera.

Содержание CyberDome II





























































Результаты поиска

Содержание CyberDome II

Отзывы:

Похожие инструкции для CyberDome II

Бренды по названию

Популярные бренды

GE CyberDome II, Руководство пользователя

Результаты поиска

Содержание CyberDome II

Отзывы:

Похожие инструкции для CyberDome II

Бренды по названию

Популярные бренды