manualshive.com logo in svg

GE Concord express, Руководство по установке

Поделиться
Скачать
GE Concord express Скачать руководство пользователя страница 18

Installing the System

13

Note  

Some versions of this siren 
may have two wires of each 
color. Only one black wire 
and one yellow wire are 
needed for panel connec-
tions.

For UL Listed installations, you can connect only one 15-Watt, Dual-Tone Siren to panel termi-
nals 3 and 7 as shown in Figure 12. For all other installations, connect up to two sirens. This siren 
does not require an end-of-line resistor.

Hardwire Siren (13-046)

Connect one or two sirens to the panel with supervision as shown in Figure 13. If Siren Verify is 
turned off (see the section “Programming the Panel”), the 2k end-of-line resistor is not required.

Note  

For UL Listed systems, 
Siren Verify must be on and 
the 2k end-of-line resistor 
installed.

Figure 13.  Connecting Hardwire Siren 13-046

Note  

Piezo siren connections to 
terminal 8 require a 2k 
end-of-line

 

resistor that can 

be located at the panel since 
it does not supervise the cir-
cuit.

Interior Piezo Siren (30-006)

Panel terminal 8 (OUT2/OC) is an open-collector (switched path-to-ground), programmable out-
put that can handle up to a 200 mA current.

The default setting (01710) activates the output for status and alarm tones, which allows for a 
piezo siren connection without changing the output configuration number.

Connect the piezo siren to the panel terminals with a 2k end-of-line resistor as shown in 
Figure 14.

Note  

If using an external power 
supply instead of panel ter-
minal 4, the supply voltage 
must be limited to 9.5 VDC 
maximum and the negative 
side of the power supply 
must be connected to panel 
ground (terminal 3).

Figure 14.  Connecting an Interior Piezo Siren

Connecting Siren Drivers, Self-Contained Sirens, and Bells

Power for a siren driver, self-contained siren, or bell can be connected to panel terminals 7 
(OUT1/+12V) and 3 (GND).

Panel terminal 7 (OUT1/+12V) is a +12-volt programmable output. At the default configuration 
setting (00410), this output can provide up to 1.25 A during an alarm (650 mA for 
UL Listed systems) if the backup battery is connected. 

Note  

If the backup battery is not 
connected, or if the configu-
ration of panel terminal 7 is 
programmed to anything 
other than the default 
(00410), then the combined 
currents of terminal 7 (OUT 
1/+12) and terminal 4 (+12V) 
must not exceed 750 mA.

The default configuration setting (00410) activates the output during any audible alarm.

The following siren drivers, self-contained sirens, and bells have been tested and found compati-
ble for use with the panel:

•

Moose Models MPI-11 (use only 8-ohm speaker loads), MP-47, MP-47B 

•

Altronix Model ALSD2 (4- or 8-ohm speaker loads)

•

ATW Models DT-24, DS508 (both self-contained)

•

Wheelock MB-G6-12 Six-inch, 12V Bell

Refer to the manufacturer’s documentation for installation details.

3

7

G N D

O U T 1 /

+ 1 2 V

Panel
Terminals

2k Ohm EOL Resistor 49-454

(Locate at Siren)

Red

Black

3

7

G N D

O U T 1 /

+ 1 2 V

Red

Black

2k Ohm EOL Resistor 49-454

(Locate at Last Siren)

Panel
Terminals

4

8

+ 1 2 V O U T 2 /

O C

2k Ohm
Resistor
49-454

Black

Red

Panel
Terminals

Содержание Concord express













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды