GE Security NetworX Series NX-8V2 Скачать руководство пользователя страница 1

466-2339A • October 2009

© 2009 GE Security, Inc.

g

NX-8V2-Control Panel

Installation Instructions

Introduction

This is the GE 

NX-8V2-Control Panel Installation Instructions. 

Installations should only be done by trained professionals. 
Use this document to install the system with default settings 
that comply with UL requirements. 
To install the keypad, other peripherals, and sensors, refer to 
the documentation for those devices.

Installation

There are four slots for board insertions inside the metal 
enclosure, two on the top and two on the bottom. These allow 
the PC board to be positioned vertically (

Figure 1

). When you 

slide the board between the grooves of the slots, make sure 
the terminal strip is toward the front opening (toward you) to 
allow for the wire connections.

Note:  

Install the metal enclosure with the door opening from the top 

to bottom.

Figure 1. Board installation

NetworX keypad maximum wire run

Table 1

 lists wire lengths for one keypad at the end of the 

wire. When connecting more than one keypad to the end of 
the wire, a higher gauge wire is required. 

Terminal descriptions

Table 2

 describes the panel terminals..

Table 1.

Maximum keypad wire run

Length in feet

Wire gauge for NX-8V2

Wire gauge for NX320-E

250

24

22

500

20

18

1000

18

16

1500

16

14

2500

14

12

Table 2.

NX-8V2 terminals

Terminal

Description

R1

House telephone ring (grey).

R

Telephone ring (red).

T

Telephone tip (green).

T1

House telephone tip (brown).

EARTH

Earth ground. Connect to a cold water pipe or a 6 to 10 ft. 

driven rod.

AC

AC input. Connect to a 16.5 V, 40 or 50 VA Class II UL 

approved transformer.

Bell + and 

Bell -

If used as a siren output (default), the speaker rating should 

be 15 watt at 8 or 16 ohm, or 30/40 watt at 4, 8, or 16 ohms. If 

voltage ouput is selected in location 37, this output becomes 

voltage output, 12 VDC, 1 Amp maximum load. Note: A 3.3 

kohm resistor may be required across the bell terminals 

when a 12 VDC siren is used. If no resistor is used, you may 

experience voltage leakage into the siren, which will cause 

these devices to output a small signal.

KP DATA

Connect to the data terminal on the keypads and the 

expanders. Maximum number of devices (keypads plus 

expanders) is 32. See Maximum Wire Run table. 

KP COM

Connect to the common terminal on the keypads and the 

expanders.

KP POS

Connect to the POS terminal on the keypads and the 

expanders. Individually, this terminal is limited to 1 amp. 

Combined, this terminal and AUX PWR+ are limited to 2 amps 

total current.

SMOKE+

Smoke detector power 12 VDC, 1.5 amps maximum (for those 

jurisdictions which allow the Priority zone to be used with 

smoke detectors).

COM

Common negative wire of powered devices such as motion 

detectors and smoke detectors.

AUX PWR+

Connect positive wire of all powered devices except smoke 

detectors and keypads. Individually, this terminal is limited to 

1 amp. Combined, this terminal and KP POS are limited to 2 

amps total current.

ZONE 8

Connect to one side of zone 8 loop. Connect the other side to 

com terminal. Open or short causes alarm. Only zone 8 may 

be used for a two-wire smoke detector using a 680 ohm EOL 

resistor.  Refer to the wiring diagram. Program location 37, 

segment 6, option 1. 

COM

Common (-) terminal for zones 7 and 8.

ZONE 7

Connect to one side of zone 7 loop. Connect the other side to 

COM terminal. Open or short causes alarm.

ZONES 6 to 

1

Connect as described for zones 7 and 8. Only zone 8 can be a 

two-wire zone. Refer to the wiring diagram for examples.

AUX 1 to 

AUX 4

Connect negative lead of low current device [relay, LED 

(install 1kohm resistor in series with LED), etc.] Connect posi-

tive lead of device to COM. Current is limited to 50 mA when 

output is negative, and 250 uA when output is positive.

Содержание NetworX Series NX-8V2











Отзывы: