GE Reuter-Stokes FLAME TRACKER Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 15

GE Reuter-Stokes FLAME TRACKER Скачать руководство пользователя страница 15

FS-9001OM

– REV M

10

Copyright 2016 GE Reuter-Stokes. All rights reserved

4

MAINTENANCE

4.1 WARNING

Do not disconnect connector while circuit is energized (or live), unless area is known to be non-hazardous.

4.2 CAUTION

The operating temperature range of the Flame Sensor is

-40°C to 150°C

.

Do not

attempt to work on the

Flame Sensor or the cable until they have reached a safe handling temperature.

The Flame Sensor output will deteriorate as the lens becomes dirty. It is recommended, when initially

installed, that the signal level be recorded during normal operation. During subsequent running, the signal
level should be compared with the initial values. If a significant reduction in the signal level is noticed, then it is
recommended that the lens be cleaned at the next opportunity (with the turbine shut down and cold). Clean the
lens with isopropyl alcohol or other residue free solvent compatible with Sapphire. In order to reduce the risk of
galling, an anti seize compound should be applied to the mounting thread prior to reinstallation of the sensor.

5

TROUBLESHOOTING

5.1 WARNING

Do not disconnect connector while circuit is energized (or live), unless area is known to be non-hazardous.

5.2 CAUTION

The operating temperature range of the Flame Sensor is

-40°C to 150°C

.

Do not

attempt to work on the

Flame Sensor or the cable until they have cooled to a safe handling temperature.

PROBLEM

CAUSE

SOLUTION

No current flows

Reversed polarity
Open wire

Change polarity
Check connections

Low sensitivity during checkout or
operation

Dirty lens
Grounded cable

Clean lens (Section 4.0)
Check cable for grounds

Low flame intensity signal during
operation

Misalignment of the sensor mount

Check the squareness of all flanges
and pipes of the sensor mount. Verify
that the sensors have a clear view of
the flame.

Periodic low reading on secondaries
of DLN1 turbines

Condensation on the lens that can
occur under high humidity
situations.

A shorter mount tube (PN# E1-
0058P002), is available from GE
Reuter Stokes and may improve this
condition. Please contact GE Reuter
Stokes for further information.

«
...
13
14
15

Содержание FLAME TRACKER
















Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды