GE Interlogix 840 Скачать руководство пользователя

Страница: 30 / 34

Model 840/845 Contactless Smart Card Reader

Technical Specifications

Operating Temperature Range:

-25

C to +85

C (-13

F to 185

F).

Humidity Range:

0% to 95% Non-condensing

Index of Protection:

IP22 (IEC 529)

Physical Dimensions:

Model 84x:

4.75 in (H) x 3.000 in (W) x 1.7 in (D)
121 mm

x 76.2 mm

x 43.2 mm

Parts Lists:

•

Model 840 Reader

•

Model 845 Reader

•

Optional Tamper Key Tool

Refer to the CASI Product Catalog for part numbers and ordering
information.

Maximum Cabling Distance:

The maximum cable distance between the

reader and the microcontroller is influenced by a number of factors
including wire gauge. See Table 1 “Cable Distances,” on page 6.

NOTE: The reader will work well with unshielded cable in most
environments. No company, including GE Interlogix, can guarantee that data
will be reliably transmitted over long distances on unshielded cable in every
installation.

Power Supply:

Nominal 12VDC, 140 mA

Color:

Light Grey

Smart Card ID:

12 digits

Card Support:

MIFARE

1 type cards

Содержание 840



































Результаты поиска

Содержание 840

Отзывы:

Похожие инструкции для 840

Бренды по названию

Популярные бренды

GE Interlogix 840, Руководство по установке

Результаты поиска

Содержание 840

Отзывы:

Похожие инструкции для 840

Бренды по названию

Популярные бренды