GE Interlogix 840 Скачать руководство пользователя | Manualshive

Страница: 10 / 34

background image

6

Model 840/845 Contactless Smart Card Reader

Connecting the Reader

Cabling Distances

The table below gives the maximum cabling distances between the reader
and the microcontroller.

NOTES:

1.

Reader supply voltage measured at microcontroller: 13.6V is nominal
when line-powered; 12V is nominal when battery-powered.

2.

All cable distances are typical maximums.

3.

Readers powered by a local 12VDC power supply will have a maximum
cable distance of 500 feet (152m) of 24 AWG telephone wire.

4.

The reader will work well with unshielded cable in most environments.
No company can guarantee that data will be reliably transmitted for long
distances on unshielded cable in every installation. Typical Wiegand
reader installation requires eight-conductor shielded cable to provide
reader power, controller communication, door contact, exit push
button, and tamper switch status. The same functionality is provided by
Proximity Perfect readers, "supervised" with four-conductor unshielded
cable.

TABLE 1: Cable Distances

13.6 Volts (see Note 1)
18

AWG

24

AWG

12 Volts (see Note 1)
18

AWG

24

AWG

2750 ft
838m

750 ft
229m

2000 ft
610m

500 ft
152m

«
...
8
9
10
11
12
...
»

Содержание 840



































Отзывы:

Нет отзывов

Похожие инструкции для 840

Бренд: H&S Страницы: 40

Бренд: Teac Страницы: 59

Бренд: Teac Страницы: 32

Бренд: Teac Страницы: 17

Бренд: EarthWay Страницы: 10

Бренд: Axxera Страницы: 32

Бренд: VDO Страницы: 14

AEC-67160 Ultra160

Бренд: Acard Страницы: 39

Бренд: Advantech Страницы: 6

Бренд: Gearmore Страницы: 36

Бренд: Sunrich Tech Страницы: 11

Бренд: NEXT Biometrics Страницы: 8

Бренд: Honda Страницы: 20

Бренд: Boss Audio Systems Страницы: 29

Бренд: Boss Audio Systems Страницы: 18

Бренд: Nokia Страницы: 6

Бренд: Nokia Страницы: 30

Бренд: LG Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды