GDS C1 Скачать руководство пользователя страница 54 | Manualshive

Страница: 54 / 56

background image

C1 Controller Users Manual

Revision 4.6

49

Dipole and collinear antennas provide best performance when installed with at least 1 to
2 “wavelengths” clearance of walls or steelwork. The wavelength is based on the
frequency:

Wavelength in meters = 300 / frequency in MHz

Wavelength in feet = 1000 / frequency in MHz

Therefore, 900 MHZ antennas require at least 2/3 meter (2 feet) and 2.4GHz 15 cm (6
inches). Antennas may be mounted with less clearance but radiation will be reduced. If
the radio path is short this won’t matter. It is important the antenna mounting bracket to
well connected to “earth” or “ground” for good lightning surge protection.

7.5.2 YAGI

ANTENNAS

Yagi antennas are directional along the central beam of the antenna. The folded element
is towards the back and the antenna should be “pointed” in the direction of the
transmission. Yagis should also be mounted with at least 1 to 2 wavelengths of clearance
from other objects. The polarity of the antenna is the same as the direction of the
orthogonal elements. For example, if the elements are vertical the Yagi transmits with
vertical polarity.

In networks spread over wide areas, it is common for a central unit to have an omni-
directional antenna and the remote units to have Yagi antennas. In this case, as the omni-
directional antenna will be mounted with vertical polarity, then the Yagi’s must also have
vertical polarity. Care needs to be taken to ensure the Yagi is aligned correctly to achieve
optimum performance.

Two Yagis can be used for a point-to-to link. In this case they can be mounted with the
elements horizontally to give horizontal polarity. There is a large degree of RF isolation
between horizontal and vertical polarity (approx –30dB) so this installation method is a
good idea if there is a large amount of interference from another system close by
transmitting vertical polarity.

An important mounting tip – if a Yagi has drainage holes in the dipole element, do not
mount the antenna with the drainage.

7.5.3

MOUNTING NEAR OTHER ANTENNAS

Avoid mounting your network’s antenna near any other antenna even when the other
antenna is transmitting on a different radio band. High RF energy of the transmission
from a close antenna can “deafen” a receiver. This is a common cause of problems with
wireless systems.

Because antennas are designed to transmit parallel to the ground rather than up or down,
vertical separation between antennas is a lot more effective than horizontal separation. If
mounting near another antenna cannot be avoided, mounting it beneath or above the other
antenna is better than mounting beside it. Using different polarity to the other antenna (if
possible) will also help to isolate the RF coupling.

«
...
52
53
54
55
56
»

Содержание C1

























































Отзывы:

Нет отзывов

Похожие инструкции для C1

615 Series ANSI

Бренд: ABB Страницы: 60

Бренд: Galcon Страницы: 32

Max Charge MC-624

Бренд: Balmar Страницы: 8

MAX CHARGE MC-614

Бренд: Balmar Страницы: 20

Бренд: Caen Страницы: 20

Бренд: Ublox Страницы: 2

Бренд: u-blox Страницы: 19

Бренд: Technische Alternative Страницы: 68

Бренд: TechGrow Страницы: 34

Бренд: CORNING Страницы: 12

Бренд: Cypress Страницы: 3

IB-TRON 4000 SOL

Бренд: INSBUD Страницы: 14

Бренд: babyplus Страницы: 28

Бренд: Blucave Страницы: 2

Бренд: Radionics Страницы: 18

Бренд: Renogy Страницы: 36

Бренд: A & H Страницы: 35

Бренд: Cypress Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды