37-1-614 Page 7
LIST OF ILLUSTRATIONS
FIGURE 2-1 – OPERATING PRINCIPLE ....................................................................................................................10
FIGURE 2-2 – ACCESSORIES AND SAFETY DEVICES ...........................................................................................11
FIGURE 2-3 – BELT DRIVE OVERHUNG LOAD CALCULATIONS............................................................................14
FIGURE 2-4 – OUTLINE DIMENSIONS .....................................................................................................................18
FIGURE 2-5 – OUTLINE DIMENSIONS .....................................................................................................................18
FIGURE 3-1 – MAXIMUM RATING..............................................................................................................................19
FIGURE 3-2– INLET WATER INJECTION DIAGRAM.................................................................................................20
FIGURE 3-3 – LIQUID RATE.......................................................................................................................................20
FIGURE 3 4 – WATER QUALITY REQUIREMENTS...................................................................................................21
FIGURE 3-5 – ALTITUDE – PRESSURE/VACUUM ....................................................................................................22
FIGURE 3-6 – MINIMUM SPEED, MAXIMUM PRESSURE OR VACUUM .................................................................23
FIGURE 4-1 – AEON PD SYNTHETIC LUBRICANT
..................................................................................................25
FIGURE 4-2 – SYNTHETIC LUBRICANT CHART.......................................................................................................25
FIGURE 4-3 – NON SYNTHETIC LUBRICANT CHART..............................................................................................27
FIGURE 4-4 – OIL BATH FILTER................................................................................................................................28
FIGURE 4-5 – OIL WETTED FILTER - SILENCER .....................................................................................................28
FIGURE 4-6 – DRY TYPE FILTER AND FILTER-SILENCER .....................................................................................28
FIGURE 6-1 – ADAPTOR PLATE................................................................................................................................37
FIGURE 6-2 – ALTERNATE ADAPTOR PLATES .......................................................................................................37
FIGURE 6-3 – BEARING CARRIER ............................................................................................................................38
FIGURE 6-4 – BEARING CLAMP PLATE....................................................................................................................38
FIGURE 6-5 - PULLER ................................................................................................................................................38
FIGURE 6-6 – ROTOR REMOVAL ..............................................................................................................................39
FIGURE 6-7 – BEARING CARRIER ............................................................................................................................39
FIGURE 7-1 – ROTOR SHAFT SEAL
..........................................................................................................................41
FIGURE 7-2 – BEARING SPACER..............................................................................................................................41
FIGURE 7-3 – DISCHARGE OPENING.......................................................................................................................41
FIGURE 7-4 – ROTORS ..............................................................................................................................................41
FIGURE 7-5 – ANGULAR CONTACT BEARING ASSEMBLY ....................................................................................42
FIGURE 7-6 – BEARING INSTALLATION...................................................................................................................42
FIGURE 7-7 – DISCHARGE END BEARING CARRIER .............................................................................................42
FIGURE 7-8 – ROTOR END CLEARNACE CHART (UNIT COLD) .............................................................................43
FIGURE 7-9 – DEPTH MICROMETER........................................................................................................................43
FIGURE 7-10 – OUTSIDE MICROMETER ..................................................................................................................43
FIGURE 7-11 – DISCHARGE OPENING.....................................................................................................................44
FIGURE 7-12 – DIAL INDICATOR...............................................................................................................................44
FIGURE 7-13 – SEAL INSTALLATION GUIDE............................................................................................................45
FIGURE 7-14 – SEAL INSTALLATION GUIDE............................................................................................................45
FIGURE 7-15 – BEARING SHIMS ...............................................................................................................................46
FIGURE 7-16 – BEARING SHIMS ...............................................................................................................................46
FIGURE 7-17 – BEARING PRESS PLATE..................................................................................................................47
FIGURE 7-18 – BEARING CLAMP PLATES ...............................................................................................................47
FIGURE 7-19 – DISCHARGE END CLEARANCE CHECK .........................................................................................47
FIGURE 7-20 – OIL SLINGER.....................................................................................................................................47
FIGURE 7-21 – END COVER ASSEMBLY..................................................................................................................48
FIGURE 7-22 – BEARING BORE ................................................................................................................................48
FIGURE 7-23 – DEPTH MICROMETER......................................................................................................................48
FIGURE 7-24 – OIL SEAL ON GATE ROTOR SHAFT ASSEMBLY............................................................................49
FIGURE 7-25 – SLIDE SHIMS OVER SHAFT ASSEMBLY.........................................................................................50
FIGURE 7-26 – PRESS PLATE & JACK SCREW ASSEMBLY...................................................................................50
FIGURE 7-27 – INTALL HUB & PINION PULL TIGHT ................................................................................................50
FIGURE 7-28 – SMALLEST MINUS READING ...........................................................................................................51
FIGURE 7-29 – SMALLEST PLUS READING .............................................................................................................51
FIGURE 7-30 – SETTING THE INTERLOBE CLEARANCE........................................................................................52
FIGURE 7-31 – HOLD GEAR & SHAFT FROM TURNING TIGHTEN FIVE GEAR TO HUB ......................................52
FIGURE 7-32 – FASTENER TORQUE VALUES .........................................................................................................52
FIGURE 7-33 – FASTENERS & LOCKNUT – TORQUE VALUES CHART.................................................................53
