gCreate gMax Printer 1.5+ Скачать руководство пользователя страница 1

Страница: 1 / 11

Page 1

gMax Printer 1.5+

Quick Start Guide

v1.0 – 8.20.15

S u m m a r y :

This guide should be used after you have received the printer and followed the unboxing instructions.
This manual can be used as a “Quick Start” guide to using the printer as well as a refresher on using the
printer in the future.

To jump straight to bed leveling check out page 8

M a c h i n e S p e c i f i c a t i o n s ( F o r R e f e r e n c e )

Max Hotend Temperature:

243C

(Do not set your max temperature above
235C to prevent a “MAXTEMP” error)

Layer Height:

0.080mm (Min) - 0.36mm (Max)

IMPORTANT!

For best results you must set your layer
heights in 40 micron increments. Ex
0.08mm, 0.12mm, 0.16mm etc…

Filament Diameter:

1.75mm

Firmware:

Marlin (Slightly Modified)

Electronics:

Ramps v1.4, Arduino, 1/16” Microstepping

Содержание gMax Printer 1.5+












Результаты поиска

Содержание gMax Printer 1.5+

Отзывы:

Похожие инструкции для gMax Printer 1.5+

Бренды по названию

Популярные бренды

gCreate gMax Printer 1.5+, Быстрый старт

Результаты поиска

Содержание gMax Printer 1.5+

Отзывы:

Похожие инструкции для gMax Printer 1.5+

Бренды по названию

Популярные бренды