background image

GBC 620os 

 

Operation Manual 

 

© 2007 General Binding Corporation  

 

Page 23 

 

MAINTENANCE 

 

Caring For the GBC 620os Laminator 

 

GBC offers Cleaning kits as well as Extended Maintenance Agreements. 

Contact your local GBC Service Representative or your dealer/distributor for additional information. The only maintenance required by the 
operator is to periodically clean the heat rollers and schedule semi annual maintenance checks. The following procedure will help keep the heat 
rollers free of adhesive that has been deposited along the edge of the laminating film. Proper alignment of the rolls of film reduces the amount of 
“squeeze out”. 

 

 

WARNING:   Do not attempt to laminate adhesives marked “Flammable”. 

 

Do not laminate glitter and/ or metallic items. Damage to the rollers may result. 

 

 

WARNING:   Do not apply any cleaning fluids or solvents to the rollers. Some solvents and fluids could ignite on heated  

  

rollers. 

 

 

Never clean rollers with sharp or pointed objects. 

 

 

Hardened adhesive deposits on the rollers can cause damage to the rollers. Rotate the rollers at the lowest speed 

 

 

setting on the control panel. 

 

 

CAUTION:  

THE FOLLOWING PROCEDURE IS PERFORMED WHILE THE LAMINATOR IS HOT. USE EXTREME  

  

CAUTION. 

 

1.

 

Remove the film from the laminator following the Procedure outlined in steps 1 through 6 of the section entitled TO UNWEB THE 
LAMINATOR. 

2.

 

Preheat the laminator until the “READY” indicator illuminates. 

3.

 

Rub the top and bottom heat rollers with cotton Cloth and alcohol. DO NOT USE METAL SCOURING PADS! 

4.

 

Refer to the beginning of the section entitled OPERATING INSTRUCTIONS to web your laminator. 

 

NOTE:

   Do not use metal scouring pads to clean the rollers. 

 

 

SERVICE AGREEMENT 

 

GBC’s Equipment Maintenance Agreement will insure the quality performance and long life built into your laminator. 

A service charge for travel time, labor and parts may be incurred for each out of warranty service call. GBC’s Equipment Maintenance 
Agreement 

Decreases these expenses and protects your valuable investment. GBC offers several types of agreements to suit your needs and budget. To 
contact 

 

GBC write to: 

 

GBC NATIONAL SERVICE 

 

 

IN CANADA:

 GBC 

NATIONAL 

SERVICE 

ONE 

GBC 

PLAZA 

     49 

RAILSIDE 

ROAD 

NORTHBROOK, IL 60062 U.S.A. 

   DON 

MILLS, 

ONTARIO 

                                                                                                                              M3A 1B3                          

 

General Binding Corporation 

One GBC Plaza 

Northbrook, IL 60062-4195 

 

 

 

 

 

 

 

EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500

Содержание 620OS
























Отзывы: