background image

Instructions for SW200DC

www.gatexpertstore.com

1

Dear users,
Thank you for choosing this product. Please read the manual carefully before assembling
and using it. Please do not leave out the manual if you send this product to a third party.

1. Safety Instruction

Please read this manual carefully before installation, in which involves with important
information about installation

using

maintenance and safety.

Any undefined operations under this manual is not allowed, incorrect using may
damage the product even causing the injuries or property losses.

To consider the possible danger during the installation or using process of swing gate
operator, installation must strictly comply with the construction standard and electrical
operating procedure.

Before installation, please make sure that the power voltage being used matches with
the supply voltage of this product. Please check if the leakage protection switch is
installed and the grounding system is correct.

Please check if additional equipment or materials are required to meet the specific
requirements.

The disposal of packaging material must be complying with the local regulation.

Please do not change any parts except for those defined under this manual. Any
undefined changes may cause the malfunction. Any damages to the product arising
therefrom shall be beyond the liability of the company.

Please do not leak water or any liquid into the controller or any other open devices.
Please disconnect the power immediately if any mentioned cases happened.

Please keep this product away from heat and open fire. Or it may damage the
components; cause the failure or other hazards.

Please make sure there is no vehicles

passengers and objects passing through while

the swing gate is moving.

Anti-clip equipment like infrared protection switch must be installed to avoid injuries to
person and property losses. The company shall not be liable for any damage or
accident arising therefrom.

The installation

using and maintenance of this product must be carried out by

professionals.

Children are not allowed be touch the control devices or remote transmitters.

A warning sign must be placed somewhere on the swing gate according to the
national standard.

Please keep this instruction properly for future reference.

Содержание SW200DC
































Отзывы: