Gateway E-5400 Скачать руководство пользователя

Страница: 98 / 130

Modem problems

Modem problems

The modem is not recognized by the system

Probable Cause

Solution

The modem has not
been added as new
hardware.

Add the modem as new hardware.

The modem is not
connected to a live
phone jack.

Make sure that the line connected to the
modem is live and plugged into the
appropriate port on the modem (line port).

The phone jack is
shared by another
modem or telephone.

If the modem shares the jack with another
device, make sure that the other device does
not have the port open (for instance, someone
is on the phone, or another modem is in use).

The modem is not
configured with a valid
interrupt or address.

Check the system settings for possible
conflicts. If one exists, correct the problem by
selecting an available interrupt and address.

05030.book Page 91 Monday, November 22, 1999 8:23 AM

Содержание E-5400



































































































































Результаты поиска

Содержание E-5400

Отзывы:

Похожие инструкции для E-5400

Бренды по названию

Популярные бренды

Gateway E-5400, Системное руководство

Результаты поиска

Содержание E-5400

Отзывы:

Похожие инструкции для E-5400

Бренды по названию

Популярные бренды