Gateway E-5400 Скачать руководство пользователя страница 12

Страница: 12 / 130

Rear panel

Serial port

connects to a serial device.

RJ-45 LAN connector

lets you connect to a network, and the adjacent

Indicator LEDs show LAN activity (yellow) and 100 Mbit speed (green).

Microphone-in, Audio Line-out,

and

Audio Line-in

jacks

connect audio

devices such as speakers, tape players, and microphones.

Secondary video port

connects the second monitor interface cable.

Primary video port

connects the first (or only) monitor interface cable.

Padlock tab

permits the use of a padlock to secure the system. To use the

padlock tab it must be removed from it’s shipping position and reinstalled
in the active position, as shown below.

Thumbscrews

must be loosened to remove the cover from the system.

Kennsington lock slot

lets you use a cable lock to secure the system.

Active position

Shipping position

05030.book Page 5 Monday, November 22, 1999 8:23 AM

Содержание E-5400



































































































































Результаты поиска

Содержание E-5400

Отзывы:

Бренды по названию

Популярные бренды

Gateway E-5400, Системное руководство

Результаты поиска

Содержание E-5400

Отзывы:

Бренды по названию

Популярные бренды