Gateway E-5400 Скачать руководство пользователя страница 124

Страница: 124 / 130

System specifications

117

Appendix

System specifications

The following specifications are for the standard configuration; your system
may contain optional equipment. All specifications are subject to change.

Case size

Width: 8.25-inch Depth: 18.625-inch
Height: 19.125-inch

Processors

Intel

Pentium III™ processors operating

at 500 MHz and faster

Cache

512K on processor

RAM

Four RIMM sockets on the system board
support 2.5 volt Rambus Dynamic
Random Access Memory (RDRAM)
RIMMs. Maximum memory is 2 GB

BIOS

Flash BIOS for easy updates from diskette

IDE interfaces

Two PCI IDE controllers support up to two
ATAPI/IDE devices each (hard drives or
CD-ROMs) for a total of up to four IDE
devices

Diskette drive interface

A diskette drive controller is integrated on
the system board

05030.book Page 117 Monday, November 22, 1999 8:23 AM

Содержание E-5400



































































































































Результаты поиска

Содержание E-5400

Отзывы:

Бренды по названию

Популярные бренды

Gateway E-5400, Системное руководство

Результаты поиска

Содержание E-5400

Отзывы:

Бренды по названию

Популярные бренды