GatesAir Intraplex T1 DCS-9500 CrossConnect System Скачать руководство пользователя

Страница: 105 / 106

8-Specifications

T1 CrossConnect Installation & Operation Manual

Version 2

GatesAir

8-5

Intraplex Products

Affidavit for the Connection of Customer Premises Equipment to 1.544 Mbps and/or Subrate

Digital Services

For work to be performed in the certified territory of
Telco’s Name:_____________________________________________________
State of:

_________________________________________________________

County of:________________________________________________________

I, _______________________, of_____________________________________,

(Name Authorized Representative)

(Customer Name)

_______________________________________,________________________,

(Customer’s Address)

(Telephone Number)

being duly sworn, state:

I have responsibility for the operation and maintenance of the terminal equipment to be connected to

__________ 1.544 Mbps and/or ___________________ Subrate digital services. The terminal

equipment to be connected complies with Part 68 of the Commissions rules except for the encoded

analog content and billing protection specifications. With respect to encoded analog content and billing

protection:
●

I attest that all operations associated with the establishment, maintenance and adjustment of the

digital CPE with respect to encoded analog content and encoded billing information continuously

complies with Part 68 of the FCC’s Rules and Regulations.

●

The digital CPE does not transmit digital signals containing encoded analog content or billing

information which is intended to be decoded within the telecommunications network.

●

The encoded analog and billing protection is factory set and is not under the control of the

customer.

I attest that the operator(s) maintainer(s) of the digital CPE responsible for the establishment,

maintenance and adjustment of the encoded analog content and billing information has (have) been

or trained to perform these functions by successfully completing one of the following: Check

appropriate one(s):
●

A training course provided by the manufacturer/grantee of the equipment used to encode analog

signals; or

●

A training course provided by the customer or authorized representative, using training materials

and instructions provided by the manufacturer/grantee of the equipment used to encode analog

signals; or

●

An independent training course (e.g., trade school or technical institution) recognized by the

manufacturer/grantee of the equipment used to encode analog signals; or

●

In lieu of the proceeding training requirements, the operator(s) maintainer(s) is(are) under the

control of a supervisor trained in accordance with _________ above.

Содержание Intraplex T1 DCS-9500 CrossConnect System











































































































Результаты поиска

Содержание Intraplex T1 DCS-9500 CrossConnect System

Отзывы:

Похожие инструкции для Intraplex T1 DCS-9500 CrossConnect System

Бренды по названию

Популярные бренды

GatesAir Intraplex T1 DCS-9500 CrossConnect System, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Intraplex T1 DCS-9500 CrossConnect System

Отзывы:

Похожие инструкции для Intraplex T1 DCS-9500 CrossConnect System

Бренды по названию

Популярные бренды