Gasmate GM160-016 Скачать руководство пользователя страница 14

Страница: 14 / 20

LIGHTING PROCEDURE – GAS

Before lighting your Spit Roaster for the first time, read the

instructions fully to ensure the Spit Roaster is assembled

correctly and is ready for use.
Remove all point-of-sale material from the Spit Roaster.

Burner Operation & Ignition System Check

1. With cylinder valve in OFF position press the electronic

igniter button. Check for sparking to the burners.

2. Lift hood, and leave hood open until burner is fully lit.
3. If spark is not evident at the burner ignition point, check

that the ignition lead is firmly attached to the control

and sparker tip.

4. With sparking established, turn cylinder valve ON. Push

and turn control knob on to HIGH and press the ignitor

button.

5. If burner fails to light after several attempts turn off the

gas supply at cylinder and inspect for any obstructions

to the gas flow.

6. Burner will need to be lit following steps 1-5.
If re-ignition is necessary while the spit roaster is still

hot, you must wait for a minimum of 5 minutes before

commencing to re-ignite (this allows accumulated gas

fumes to clear).

After Use

Turn the gas cylinder valve off and wait for the flame to go

out. Then turn the spit roaster control valve off.

LIGHTING PROCEDURE

– CHARCOAL

1. With cylinder valve in OFF position press the electronic

igniter button. Check for sparking to the burner.

2. Lift hood, place charcoal into charcoal tray in the main

area (ensure you do not place it in the small area).

3. If spark is not evident at the burner ignition point,

check that the ignition lead is firmly attached to the

control and sparker tip.

4. With sparking established, turn cylinder valve ON. Push

and turn control knob on either side of the ignitor to

HIGH and press the ignitor button.

5. When charcoal is lit, turn the burner OFF by turning the

control knob clockwise to the OFF position.

6. If burner fails to light after several attempts turn

off the gas supply at cylinder and inspect for any

obstructions to the gas flow.

7. Burner will need to be lit following steps 1-5.
If re–ignition is necessary while the gas Spit Roaster is

still hot, you must wait for a minimum of 5 minutes before

commencing to re–ignite (this allows accumulated gas

fumes to clear).

Содержание GM160-016





















Результаты поиска

Содержание GM160-016

Отзывы:

Похожие инструкции для GM160-016

Бренды по названию

Популярные бренды

Gasmate GM160-016, Руководство пользователя

Результаты поиска

Содержание GM160-016

Отзывы:

Похожие инструкции для GM160-016

Бренды по названию

Популярные бренды