GarrettCom Magnum 6K32 Скачать руководство пользователя страница 45

Страница: 45 / 65

Magnum 6K32 Managed Switch Installation and User Guide (02/05)

www GarrettCom com

GBIC-

LXSC25

1000Mb Single-

mode

1550

9/125

-4.0 -21

37.5 17.5

GBIC-

ZXSC40

1000Mb Single-

mode

1550

9/125

-4.0 -21

60 17.5

GBIC-

ZXSC70

1000Mb Single-

mode

1550

9/125

-3.0 -23

90 20.5

102

* Note: The use of either multi-mode or single-mode fiber to operate at 100Mbps speed

over long distances (i.e., in excess of approx. 400 meters) can be achieved

only

if the following factors are both applied:

•

The 100Mb fiber segment must operate in full-duplex (FDX) mode, i.e. the
full-duplex (factory default) setting for 100Mbps fiber ports must be used,
and

•

The worst-case OPB of the fiber link must be greater than the fiber cable’s
passive Attenuation.

(Attenuation = Cable loss + LED aging loss + Insertion loss + safety factor)

5.0

Magnum 6K32 Managed Switch Port Modules

This chapter describes each Port Module (PM), including appearance,

functionality, and status displays.

5.1

Inspecting the Package and Product

This section applies only to PMs shipped as separate items, i.e., 6K32 PMs not

factory installed in a Magnum 6K32 modular slot.

Examine the shipping container for obvious damage prior to

installing a 6K32 PM; notify the carrier of any damage you believe occurred

during shipment or delivery. Inspect the contents of this package for any signs

of damage and ensure that the items listed below are included.

This package should contain:

6K32 PMs

Installation instructions, with illustrations

Remove the 6K32 PM(s) from the shipping container. Be sure to

keep the shipping container should you need to ship any of the PMs separately

at a later date. In the event there are items missing or damaged, contact your

supplier. If you need to return the unit, use the original shipping container if

possible. Refer to Chapter 5 for specific return procedures.

Содержание Magnum 6K32


































































Результаты поиска

Содержание Magnum 6K32

Отзывы:

Похожие инструкции для Magnum 6K32

Бренды по названию

Популярные бренды

GarrettCom Magnum 6K32, Руководство по установке оборудования и инструкция пользователя

Результаты поиска

Содержание Magnum 6K32

Отзывы:

Похожие инструкции для Magnum 6K32

Бренды по названию

Популярные бренды