Garmin GNS 480, Инструкция по установке

Страница: 167 / 200

Appendix D - Interconnect Diagrams
GNS 480 (CNX80) Installation Manual 560-0982-01 Rev L D-11
2345 Turner Road S.E., Salem, OR 97302
Phone: 503.581-8101 http://www.garmin.com
Garmin AT, Inc
RS-232 INTERFACES
GNS 480 INSTALLATION DRAWING
NOTES:
1. ALL WIRES 24 AWG OR LARGER UNLESS OTHERWISE SPECIFIED.
2. AT GNS 480, CONNECT SHIELD GROUNDS TO THE REAR OF THE MOUNTING FRAME
ON THE CONNECTOR PLATE -- THE SHIELD LEADS MUST BE LESS THAN 3.0 ".
CONNECT OTHER SHIELD GROUNDS TO AIRCRAFT CHASSIS WITH AS SHORT A
CONDUCTOR AS PRACTICAL.
3. RXD5 (P5-1/41) MAY BE USED INSTEAD OF RXD8 FOR ALTITUDE ENCODER. THE
GNS 480 RX SERIAL PORT MUST BE CONFIGURED FOR ALT ENC AND 1200 OR 9600
BAUD, DEPENDING UPON WHICH SERIAL ALTITUDE FORMAT IS USED. THE GNS 480
WILL ACCEPT ALTITUDE DATA IN EITHER THE APOLLO/IIMORROW FORMAT (1200
BAUD) OR SHADIN FORMAT (9600 BAUD).
4. SERIAL PORT 1 (P1-4/5/23) OR SERIAL PORT 5 (P5-1/21/41) MAY BE USED INSTEAD
OF SERIAL PORT 2 FOR F/ADC. GNS 480 RX SERIAL PORT MUST BE CONFIGURED
FOR FADC 9600 BAUD (OR FUEL 9600 BAUD IF INTERFACING TO A PC-12).
TRANSMIT PORT MUST BE CONFIGURED FOR MAPCOM 9600 BAUD.
5. TXD1 SHOWN (TXD2 SHOWN IN PARENTHESES). INSTALL JUMPER BETWEEN DB9-2
AND DB9-1 TO ENABLE 10' RESOLUTION. REFER TO TRANS-CAL INSTALLATION
MANUAL FOR ADDITIONAL DETAILS.
6. JUMPER PINS P3-3 AND P3-8 (DB-9 CONNECTOR) TO SELECT APOLLO SERIAL
ALTITUDE FORMAT, AND LEAVE OPEN TO SELECT GARMIN SERIAL ALTITUDE
FORMAT.
7. TXD1 SHOWN (TXD2 SHOWN IN PARENTHESES). PIN 4 MUST BE GROUNDED TO
SELECT APOLLO SERIAL ALTITUDE FORMAT.
8. NOT USED.
9. TAS1000 MUST BE SET UP TO TRANSMIT Z-FORMAT DATA.
10. OTHER EQUIVALENT PARTS MAY BE INTERFACED TO THE GNS 480. SEE
APPROPRIATE INSTALLATION MANUALS FOR THAT EQUIPMENT.
11. GNS 480 SERIAL PORT RXD7 (P5-10/44) MUST BE CONFIGURED FOR COG 9600
BAUD.
12. SEE APPENDIX C.2 FOR ADDITIONAL REQUIREMENTS WHEN CONFIGURING THE
GNS 480 TO PROVIDE ALTITUDE DATA TO A TRANSPONDER.
- 04/08/03
Description Rev Date
A 05/23/03
B 06/04/03
C 07/10/04
ALTITUDE
ENCODER
RS-232 TxD
GROUND
P5
30
44 SERIAL GND 7/8
RS-232 RxD8
GNS 480
TYPICAL CONNECTIONS TO ALTITUDE ENCODER
TYPICAL CONNECTIONS TO FUEL FLOW COMPUTER
TRANS-CAL
SSD120
4 (9)
5 (8)
DB9
5
ICARUS
3000U
2
5
P3
SANDIA
SAE5-35
1 (2)
5 (5)
J5
3
3
8
1
2
6
FUEL FLOW
COMPUTER
RS-232 TxD
P1
21 RS-232 RxD2
GNS 480
Miniflo-L
Microflo-L
6
DB9
SHADIN
Digiflo-L
9105xxP
5
DB15
Digiflo-L
9105xx(T-D)
J
AMP 9-pin
H 9 RS-232 TxD2 22 12 RS-232 RxD
GROUND 3 SERIAL GND 2 2 2 D
4
TYPICAL CONNECTIONS TO FUEL / AIR DATA COMPUTER
CONFIG JUMPER
4
-
-
- - CONFIG PIN
7
FUEL / AIR DATA
COMPUTER
RS-232 TxD
P1
21 RS-232 RxD2
GNS 480
Digidata
5
P1
SHADIN
F/ADC-200
F/ADC-2000
6
J2
12 RS-232 TxD2 22 5 RS-232 RxD
GROUND 3 SERIAL GND 2 10 9
4
FS-450
6
DB9
9
2
JP INSTRUMENTS
EDM-700/800
1
FF
2
25
SHADIN
8800-M
7
15
DB15
-
-
-
TAS 1000
10
DB25
23
11
INSIGHT
9
True Flow 500
2
MINI-3
-
1
INSIGHT
TYPICAL CONNECTIONS TO CARBON
MONOXIDE DETECTOR
CO DETECTOR
RS-232 TxD
P1
10 RS-232 RxD7
GNS 480
Aero 452
CO GUARDIAN
Aero 552
GROUND 44 SERIAL GND 7/8
1
DB9
7
10
P1
3
Initial Release
Added Shadin altitude encoder and clarified note 8.
Added Insight TAS1000 F/ADC and TF500 fuel flow computer.
Corrected pin no. for JPI EDM-700/800. Clarified Note 4.
Changed unit name to GNS 480. Deleted SL70/70R (moved to
Traffic/Transponder diagram). Updated notes to indicate that
GNS 480 will accept altitude data in both Apollo and Shadin format.
Added Shadin 8800-T encoder and CO Guardian detectors.
11
8800-T
7
15
DB15
-
-
-
PC10, PC12
PC20
23
DB37F
-
18
Logic
D 03/07/06
Added Pilatus PC-12 Engine Instrument System RS-232 connection
to Fuel Flow Computer diagram.
E
Added note 12 to clarify requirements when GNS 480 providing
altitude data to transponders.
01/12/07
12
F For consistency, changed RS232 to RS-232. 10/30/08
Figure D-5. RS-232 Serial Interfaces Interconnect Diagram