background image

GHP 20 Installation Instructions 

11

Configuring the GHP 20

The GHP 20 must be configured and tuned to your boat dynamics and 

motor configuration. Use the dockside wizard (if applicable) and the sea 

trial wizard on the GHC 10 to configure the GHP 20. These wizards will 

walk you through the necessary configuration steps.

about the Dockside Wizard

Notice

If you perform the dockside wizard while your boat is out of the water, 

provide rudder-movement clearance to avoid damage to the rudder or 

other objects.
You can complete the dockside wizard while your boat is in or out of 

the water. If your boat in the water, it must be stationary while you 

complete the wizard.

Performing the Dockside Wizard

Notice

Not all of the steps listed in this section may apply to your boat. If one 

of the steps listed as “if applicable” does not appear on the GHC 10, 

proceed to the next step.
1.  Turn on the GHP 20.
  The first time you turn on the GHP 20, you are prompted to 

complete a short setup sequence on the GHC 10.

2.  If necessary, complete the setup sequence.
3.  Start the dockside wizard (

page 11

).

4.  If applicable, select the vessel type.
5.  If applicable, test the steering direction (

page 11

).

6.  If applicable, select the speed source and verify the tachometer 

(

page 11

).

7.  Review the wizard results (

page 11

).

Starting the Dockside Wizard

This step may not apply to all boats. If it does not appear on the 

GHC 10, proceed to the next step.
1. After you complete the initial setup, select an option:

•  If the dockside wizard starts automatically, proceed to step 2.
•  If the dockside wizard does not start automatically, select 

Menu

 

Setup

 > 

Dealer Autopilot Configuration

 > 

Wizards

 > 

Dockside Wizard

.

2. Select 

Begin

.

testing the Steering Direction

This step may not apply to all boats. If it does not appear on the 

GHC 10, proceed to the next step.
1.  Use the arrows on the GHC 10 to test the steering direction. 
  When you select the right arrow, the rudder should turn so that the 

boat would steer to the right, and when you select the left arrow, the 

rudder should turn so that the boat would steer to the left. 

2.  Select 

Continue

.

3.  Select an option:

•  If the steering test turns the boat in the correct direction, select 

Yes

.

•  If the steering test turns the boat in the opposite direction, select 

No

.

4.  If you selected 

No

 in step 3, repeat steps 1–2.

Selecting the Speed Source

This step may not apply to all boats. If it does not appear on the 

GHC 10, proceed to the next step.
If your steering system sends tachometer information to the autopilot, it 

will be automatically selected, and no NMEA 2000 tachometer or GPS 

speed source needs to be selected.

Select an option:
•  If you connected a NMEA 2000-compatible engine (or engines) 

to the NMEA 2000 network, select NMEA 2000. 

•  If tachometer data is unavailable or unusable, select 

GPS data

 

as a speed source.

 

When GPS data is used as a speed source, the maximum 

speed for all vessel types must be configured.

•  If you did not connect a speed source, select 

None

.

 

If the autopilot does not perform well using None as the 

speed source, Garmin recommends connecting a tachometer 

or GPS as the speed source.

Verifying the tachometer

This step may not apply to all boats. If it does not appear on the 

GHC 10, proceed to the next step.
  With the engine (or engines) running, compare the RPM readings on 

the GHC 10 with the tachometer (or tachometers) on the dashboard 

of your boat.

Reviewing the Results of the Dockside Wizard

The GHC 10 displays the values you chose when you ran the Dockside 

Wizard.
1.  Examine the results of the dockside wizard.
2.  Select any incorrect value and select 

Select

.

3.  Correct the value.
4.  Repeat steps 2 and 3 for all incorrect values.
5.  When you are finished reviewing the values, select 

Done

.

Содержание GHP 20





















Отзывы: