background image

GHP 20 Installation Instructions 

17

Category

Setting

Description

Navigation Setup

Navigation 

Gain

Allows you to adjust how 

aggressively the autopilot 

eliminates cross-track error 

while following a Route-To 

pattern. 

If this value is too high, the 

autopilot can oscillate back 

and forth across the course 

line over long distances. 

If this value is too low, the 

autopilot may respond slowly 

in eliminating cross-track 

error.

Navigation Setup

Navigation 

Trim Gain

Allows you to adjust the 

acceptable amount of long 

term cross-track error while 

following a Route-To pattern. 

Only adjust this setting after 

the navigation gain has been 

set.

If this value is too 

high, the autopilot will 

overcompensate for cross-

track error.

If this value is too low, the 

autopilot will allow a large 

long term cross-track error.

NOTE:

 Advanced configuration settings are available when using 

the advanced configuration procedure (

page 13

). Other settings are 

available during normal operation of the GHP 20. See the configuration 

section of the 

GHC 10 Owner’s Manual

 for more information.

Error and Warning Messages

Error Message

Cause

autopilot action

Autopilot is not 

receiving navigation 

data. Autopilot placed 

in heading hold.

The autopilot is no 

longer receiving 

valid navigation data 

while performing a 

Route-To.

This message will 

also be shown if 

navigation is stopped 

on a chartplotter prior 

to disengaging the 

autopilot.  

•  Alarm sounds

•  Autopilot transitions 

to heading hold

Connection with 

autopilot lost

The GHC lost 

connection with CCU.

N/A

Low GHC supply 

voltage

The supply voltage 

level is below the 

value specified in the 

low voltage alarm 

menu.

N/A

Lost Communication 

With Steering 

Controller

The autopilot lost 

connection with the 

boat steering system 

while the autopilot 

was engaged.

•  Alarm sounds

•  Autopilot transitions 

to standby

No Steering 

Controller Detected

The autopilot cannot 

detect the boat 

steering system when 

trying to engage.

•  Alarm sounds

•  Autopilot transitions 

to standby

Steering Controller 

Not Supported

The steering system 

of the boat is not 

compatible with the 

installed version of 

the GHP 20.

•  Alarm sounds

•  Autopilot transitions 

to standby

Содержание GHP 20





















Отзывы: