background image

Item

Description

Service Part Number

Details

Shaft

50 in. model: S00-01000-02
57 in. model: S00-01000-07

Removing the Propeller Drive Motor and Nose Cone from the Shaft

page 12

Propeller drive motor N/A

This part is replaceable by an authorized repair technician only.

Nose cone

Transducer: 010-12832-20
No transducer: 010-12832-22

One of two parts included with a replacement nose cone.
(

Replacing the Nose Cone

, page 13

)

Transducer

Contact Garmin support for 
replacement transducer options.
Transducer replacement kit: 
010-12832-25

The replacement transducer and transducer replacement kit are sold 
separately.
Detailed replacement instructions (190-02521-94) are included with the 
transducer replacement kit.

Motor anode

010-12832-35

The anode kit contains the motor anode and the propeller anode (not 
shown).

Servicing the Anodes

, page 3

Lower nose cone

Transducer: 010-12832-20
No transducer: 010-12832-22

One of two parts included with a replacement nose cone.
(

Replacing the Nose Cone

, page 13

)

Transducer pad

010-12832-25

Included in the transducer replacement kit.

Skeg

010-12832-18

Removing the Skeg and Nose Cone

, page 12

Not shown Propeller

Power propeller: 010-12832-00
Weedless propeller: 010-12832-01

Replacing the Propeller

, page 4

6

Содержание Force



























Отзывы: