background image

Item Description

Notes

Garmin BlueNet 30 
gateway

All Garmin BlueNet network devices must be connected on one "side" of the 
gateway, and all legacy Garmin Marine Network devices must be connected 
to the other "side."

NOTICE

Only one Garmin BlueNet 30 gateway can be installed in a mixed network. 
Attempting to install more than one gateway in a network will result in poor 
performance or no communication between devices.

Garmin BlueNet radar

Ignition or power switch 
(not included)

You should connect the Garmin BlueNet 30 gateway to power through the 
ignition or another physical switch. The device continues to draw power 
when the system is off and drains the battery if it is connected directly.

Legacy Garmin Marine 
Network cable

Garmin Marine Network cables have larger connectors that look more like a 
common RJ45 network connector.

Garmin BlueNet network 
cable

Garmin BlueNet network cables have smaller connectors that look more like 
NMEA 2000

®

 connectors.

NOTE: Garmin BlueNet network cables are not the same as NMEA 2000 
cables, and you cannot use them interchangeably.

12 Vdc power source

The Garmin BlueNet 30 gateway must connect to power using the included 
power cable.

Garmin BlueNet 20 switch 
or Garmin BlueNet chart­
plotter

If you are using a Garmin BlueNet 20 switch, the best practice is to connect 
that switch to the gateway. If you are not using a switch, you can connect a 
chartplotter with multiple Garmin BlueNet network ports or a single Garmin 
BlueNet chartplotter to the gateway, depending on the types of devices on 
your vessel.

Garmin BlueNet chart­
plotter or other device

NOTE: You must have at least one Garmin BlueNet chartplotter on the boat. 
The Garmin BlueNet 30 gateway is not necessary without a Garmin BlueNet 
chartplotter.

GMS 10 switch or legacy 
Garmin Marine Network 
chartplotter

If you are using a GMS 10 switch, it is the best practice to connect that 
switch to the gateway. If you are not using a switch, you can connect a 
chartplotter with multiple legacy Garmin Marine Network ports or up to two 
single legacy Garmin Marine Network devices to the gateway, depending on 
the types of devices on your vessel.

Legacy Garmin Marine 
Network chartplotter or 
other device

5

Содержание BLUENET 30









Отзывы: