background image

Part #4519655 Rev.2 (Jan 27/15)

Page 8

OPERATION

Hot Plate – Model G24-15H

Pilot Burner Adjustment

1.  Remove ring grates and top grate, if not already removed.

2.  Adjust the pilot valve, located on the manifold between 

the two burner valves, to a yellow fl ame 1/2 inch (13 mm) 
long (This adjustment can be made through the opening 
in the upper front panel, around the rear burner valve.)

3.  Replace ring grates and top grate.

To Operate Main Burner

1.  Hi-speed non-clog burners light automatically from the 

pilot.

2.  Turn left valve full “ON” to light front burner. Turn right 

valve full “ON” to light rear burner.

G24 Griddles

Lighting & Pilot Burner Adjustment

Each griddle burner is equipped with a pilot. 

For the HI-LO valve operated model, the pilot adjusting valve 
burner pilot is located on the manifold to the right of each 
griddle valve. Open the pilot valve with a screwdriver and 
light the pilot with a match.

For the griddle equipped with thermostats (GTHX) the pilot is 
located to the left of the ON-OFF valve. Open the pilot valve 
with a screwdriver and light the pilot with a match. 

Pilots fl ames must be 3/4 inch (19mm) long .

Hi-Lo Valve Adjustment

Griddles equipped with Hi-Lo valves require a low fl ame 
setting. To adjust, proceed as follows:

1.  Burner must be cold.

2.  Be sure pilot fl ames are lit and adjusted.

3.  Turn dial to “LO” position, then remove dial.

4.  With a screwdriver, turn the small adjusting screw inside 

the valve stem and adjust to obtain the low cooking 
temperature desired, maintaining a stable fl ame covering 
the entire burner (minimum 3/16 inch (5 mm) long 
fl ame)).

5.  Replace dial and turn to “OFF” position.

Calibration Instructions

1.  Use a test instrument with a special disc type 

thermocouple or a reliable surface type pyrometer. Note: 
a drop of oil on the face of the disc will provide better 
contact with the plate.

2.  Set all griddle thermostats to 350°F. In order to allow the 

griddle temperature to stabilize, the thermostats must be 
allowed to cycle twice before taking a test reading.

3.  Check the griddle temperature when the thermostat just 

cycles “OFF” by placing the thermocouple fi rmly on the 
griddle surface directly above the sensing bulb of the 
thermostat. The reading should be between 335°F and 
365°F. If the reading is outside of these limits, calibrate as 
follows:

4.  Carefully remove the dial, not disturbing the shaft 

position.

5.  Hold the shaft steady and with a small fl at screw driver 

turn the calibration screw located inside the shaft 
clockwise to decrease temperature or anti-clockwise to 
increase temperature. Note: Each 1/4 turn of the screw 
will create a change of approximately 25°F.

6.  Replace the thermostat dial and repeat steps 1 through 3 

to verify that a correct adjustment has been made.

G20-SP and G20-SPH Stock Pot Range

Pilot Burner Adjustment

G20-SP Stock Pot Range

1.  The pilot adjusting valve is located on the manifold.

2.  With valve panel in place, the pilot can be adjusted with a 

long thin screwdriver to obtain a 7/16 inch (11 mm) long 
fl ame. (This adjustment can be made through the small 
hole located on the valve panel.)

Содержание G24 SERIES

























Отзывы: