![background image](http://html2.mh-extra.com/html/garland/932-sg/932-sg_instruction-manual_5063217036.webp)
English
36/132
It is neccesary to pay attention to posible loosening or
overheating of parts of the machine.
If you detect any anomalies stop inmediatly the
machine and check it carefully. In case of failure take
the machine to the repair service.
In any case you should continue working if you feel
that the performance is not correct.
Remember to always use the machine with clean
hands and without petrol and oil.
Clean the work area and eliminate any obstacles that
could cause accidents. Check the working area and
remove any objects that could cause the cutting tool
of the machine to get tangled on. Also remove any
parts that the cutting tool could violently hit causing
these to move in the direction of the user or other
people and/or animals.
Do not allow any other person into the work area.
All other people must be at least at a distance of 15
metres as it is a dangerous area.
Never leave this machine unattended.
It is imperative that the engine is turned off when
carrying the machine from one working area to another.
Never touch elements that can be hot during
the start up or operating the machine, for
example, the escape, sparks or high voltage
cables.
Do not use accessories except those recommended
by our company as otherwise the use of other non
original accessories could cause severe damages to
the end user, to passers-by and to the machine.
Always follow the safety rules stated in this manual.
7.1. FIXING THE MACHINE AND GUIDANCE
Hold the machine with hands on the handles and with
the right hand in such a position that you can action
the controls (accelerator and security switch).
Attention! So as to reduce the risk of loss of control
and possible damages (that could even be fatal) to the
end user and/or those surrounding him, never use this
machine single handedly.
USE:
WARNING: Wear eye and audible protection at all
times.
Before starting the machine, place the correct drill for
the diameter of the hole to be done.
Once the drill has been placed, start the machine and
put it in a vertical position, propping the point of the
drill in the centre of the hole to be done.
Hold the machine strongly, slightly elevated and
accelerate so that the drill begins to turn.
Accelerate the machine up to 70% so that the drill
achieves the adequate speed.
Содержание 932 SG
