GB
- 29 -
8.2 Maintenance
Replacing the saw chain and cutter rail
The cutter rail needs to be replaced if
•
the guide groove of the cutter rail is worn;
•
the nose sprocket in the cutter rail is dama-
ged or worn.
Remove the adapter plate (Item 19) from the
cutter rail as shown in Fig. 27. Now
fi
t the adapter
plate to the new cutter rail. Proceed as described
in the section “Assembly of the cutter rail and the
saw chain”.
Checking the automatic chain lubrication
You should check the operation of the automatic
chain lubrication system on a regular basis in or-
der to guard against overheating and the associ-
ated damage to the cutter rail and the saw chain.
To do this, point the tip of the cutter rail towards a
smooth surface (board, section of a cut tree) and
allow the chainsaw to run.
If an increasing oil trace becomes evident during
this process then the automatic chain lubrication
system is working properly. If no clear oil trace is
evident then please refer to the corresponding
instructions in “Troubleshooting”. If the information
contained there still fails to remedy the situation
then please contact our service department or
another similarly quali
fi
ed workshop.
Danger!
Do not actually touch the surface with
the tip of the cutter rail when performing this test.
Keep a safe distance (approx. 20 cm).
Sharpening the saw chain
E
ff
ective working with the chainsaw is only pos-
sible if the saw chain is in good condition and
sharp. This also reduces the risk of kickback.
The saw chain can be re-sharpened by any dea-
ler. Do not attempt to sharpen the saw chain your-
self unless you have the necessary special tools
and experience.
8.3 Ordering replacement parts:
Please quote the following data when ordering
replacement parts:
•
Type of machine
•
Article number of the machine
•
Identification number of the machine
•
Replacement part number of the part required
For our latest prices and information please go to
www.isc-gmbh.info
9. Notes on environmental
protection / disposal
The equipment is supplied in packaging to pre-
vent it from being damaged in transit. The raw
materials in this packaging can be reused or
recycled. The equipment and its accessories are
made of various types of material, such as metal
and plastic. Never place defective equipment in
your household refuse. The equipment should
be taken to a suitable collection center for proper
disposal. If you do not know the whereabouts of
such a collection point, you should ask in your
local council o
ffi
ces.
10. Storage
Store the equipment and accessories out of
children’s reach in a dark and dry place at above
freezing temperature. The ideal storage tempe-
rature is between 5 and 30 °C. Store the electric
tool in its original packaging.
Anl_GAK_E_20_Li_OA_SPK7.indb 29
Anl_GAK_E_20_Li_OA_SPK7.indb 29
19.04.2016 15:06:20
19.04.2016 15:06:20
Содержание GAK-E 20 Li OA
Страница 177: ...BG 177 11 Anl_GAK_E_20_Li_OA_SPK7 indb 177 Anl_GAK_E_20_Li_OA_SPK7 indb 177 19 04 2016 15 06 40 19 04 2016 15 06 40...
Страница 230: ...RU 230 11 Anl_GAK_E_20_Li_OA_SPK7 indb 230 Anl_GAK_E_20_Li_OA_SPK7 indb 230 19 04 2016 15 06 45 19 04 2016 15 06 45...
Страница 340: ...EH 04 2016 01 Anl_GAK_E_20_Li_OA_SPK7 indb 340 Anl_GAK_E_20_Li_OA_SPK7 indb 340 19 04 2016 15 06 55 19 04 2016 15 06 55...