21
adjusting this bolt if required. If you are not
proficient in base throttle adjustment let this be
done by a person with suitable knowledge and
experience. (fig. D3)
Pull the throttle cable out of the cable collet and
hang it into the slot as shown in Figure D4.
Activate throttle lever completely, make sure that
throttle plate touches the stopper (a). Release
throttle lever, be sure that throttle plate returns
automatically and touches the idle screw (b).
Then fix the nuts (c). (fig. D5, D6)
Stick the two ends of the red cables together as
shown in Figure E1.
Stick the ends of the two black cables together
as shown in Figure E2.
4.1 Cutter assembly (fig. F1-F6)
Take care to have the slider in STOP position (fig.
F1)
Mount the cutter as shown from Figure F1 to F6.
To block the mowing arbor insert e.g. the allen
key through the borings of the cover and arbor
whilst fastening the cutter blade onto the arbor
with the fastening nut and hex nut key (27, 29).
See Figure F6 for reference.
4.2 Trimmer assembly(fig. F7)
Take care to have the slider in STOP position. (fig.
F7)
Block the arbor the same way as described for
cutter assembly.
Screw the trimmer onto the arbor as firm as
possible.
5. OPERATION INSTRUCTIONS
IMPORTANT
Do not operate the engine at maximum
speed right from the start, as the engine
itself as well as the gearing components
need a running-in time. The engine itself reaches
its maximum capacity after the first 10 hours of
operation.
Non-compliance with this instruction
reduces your engines lifespan substantially.
5.1 Cold starting
· Turn the choker into the position like shown
in Fig. G.
· Put the slider (I-2) into START position as
shown in fig. I
· Pull the starter cable grip gently until you feel
resistance, and then briskly outwards to
start the engine 3-4 times.
· When the engine’s running, you have to turn
the choker to "ON" position again by bringing it
back to "ON" position.
· Now accelerate for the required rotation
speed (depends on the grass length and the
driving speed) with the throttle lever (I-4).
5.2 Warm starting
This is similar to the start of a cold engine. In
this case, the choke level is always kept at "ON"
position at the bottom.
5.3 Stopping
Let the engine return to idle running without
pressing the throttle control.
· Put the slider (I-2) into STOP position as
shown in fig. I
CAUTION. The cutting tool continues rotating for
a few seconds after the engine is turned off. Hold
both handles until the cutting tool has come to
complete stop.
Working with petrol brush cutter
- When you work with the petrol brush cutter
Содержание YGL N.G.1250-1
