20
catapulted into the air by the trimmer/cutter
· Cutting injury of hand (fingers) and feet:
Never touch the trimmer/cutter attachment
during the operation.
Stay behind the operation pole and hold it
with one hand while starting the motor with
the recoil starter with the other hand.
· Burning hazard
Beware of hut exhaustion fumes.
Eninge parts like the muffler become hot
during operation!
Do not touch during operation or immediately
after operation. After operation the machine
has to cool down.
4. ASSEMBLY
references see Figures B1 and B2 respectively.
Mount the mowing pole (13) onto the mowing
collet (10) with the screw (S5). (fig. C1, C2, C3)
Take care that to place the collet mowing pole
assembly onto the frame, the mowing head
should face downwards! For further clarification
consult Fig. A
Mount the mowing protection (6) onto the
mowing pole. Place the four screws (23) through
the borings of the mowing protection collet
as shown in Fig. C5,C6 and place the mowing
protection (6) onto the 4 screws as shown in Fig.
C6. (fig C4, C5, C6)
Fix the mowing protection by tightening the four
nuts (21) with the open end wrench onto the
screws. Use the borings as shown in picture C7!
Mount the trimmer limiter (P) with the screw
(S4) by tightening it with the Phillips screwdriver
(26,27) (fig. C8)
Slip one wheel onto the wheel axis on the side of
your choice. Slip one washer (19) onto that axis
and finally tighten the wheel with the lock nut
(19.1) so that the wheel can still rotate freely ,
and then assemble another wheel in the same
way(fig. C9)
Loosen the hex head srews of the pole collet
of the frame(11) with allen key (25) as much as
possible.
Insert the pole (16) into the collet. Take care that
the support wheel is situated towards the
ground! (fig. 10)
Tighten the hex head screws again.
Now you connect the operation pole (1) to the
pole with the support wheel (16).
First, you have to slip the connecting frame (A)
onto the pole (16) and connect these two parts
with one hex head screw (17).
Then, you insert the operation pole into the
connecting frame. Dependent on your preference
regarding with which hand you prefer to operate
the throttle lever you can choose how to insert
the operation pole. Fix it as well to the connection
frame (A) with a hex head screw (17). (fig. C11)
Finally, insert the other hex head
screws into the connecting frame borings and
fasten them firmly to tighten the entire pole
assembly together! (fig. C11)
After having mounted together all major
disassembled parts of the machine, you can
adapt the operation pole assembly according to
your body height!
Loosen the 4 hex headscrews that tighten the
pole collet onto the crosspole of the
frame(11). Adjust the pole assembly in a way that
you can hold, staying upright, the steering handle
conveniently with your arms being moderately
angled.
Dismount the air-filter cover by unscrewing the
screw with Allen key (24). (fig. D1)
Remove the hex head bolt with the open wrench
(28). (fig. D2)
screw the hex head cable collet into threaded
boring so that it stands approx. 5mm through the
boring. You can later the maximum throttle by
Содержание YGL N.G.1250-1
