background image

1800 909 909 

www.powertoolsupport.com      email: [email protected]

AFTER SALES SUPPORT 

46460

11

2

General Information & Safety Instructions

DANGER!  BEWARE OF KICKBACK!

   WARNING! Kickback can lead to dangerous loss of control of the chainsaw and 

result in serious or fatal injury to the saw operator or to anyone standing close 
by. Always be alert. Rotational kickback and pinch kickback are major chainsaw 
operational dangers and the leading cause of most accidents.

Unpacking

  Due to modern mass production techniques, it is unlikely that your Gardenline

®

 

Power Tool is faulty or that a part is missing.

  If you find anything wrong, do not operate the tool until the parts have been 

replaced or the fault has been rectified.

  Failure to do so could result in serious personal injury.

Contents of carton

  The Gardenline

®

 Petrol Chainsaw is supplied with the following accessories  

as standard.

  • 1 x Instruction Manual 
  • 1 x Warranty Card & Details
  • 1 x Chain
  • 1 x Chain bar
  • 1 x Double ended wrench
  • 1 x Screwdriver
  • 1 x Sharpening file
  • 1 x Bucking spikes and screws

Содержание PCH25





























Отзывы: