Gardenline GPHS-26cc, Руководство пользователя

Страница: 10 / 16

Gardenline 23
Lubricating gear box assembly (Level 1)
Fig. 26 - 27
Tools required:
1
Grease Gun
1 Clean rag
Parts required:
1
Grease , 14 oz. or Lithium based
• Clean dirt from the grease fitting (I).
• Carefully pump grease into fitting (I). Do not force grease. Too much pressure will force
grease past seals and cause damage. Apply 1-2 pumps of grease every 15-25 hours of
operation.
• Wipe excess grease from around grease fitting.
Sharpening blades (Level 3)
Fig. 28 - 33
Tools required:
2
Wrenches, 10 mm
1 Flat file
1 Screwdriver
Parts required:
None
Warning! Hedge Trimmer Blades are very sharp. Wear gloves to protect hands.
• Disconnect spark plug wire.
• Remove blade stiffener:
• Remove two screws(J) at the bottom of front handle guard.
• Remove three screws (K) on the supporting plate for
• Remove blade stiffener locknuts (L) and washers. Do
• Remove blade stiffener.
• Fix locknuts (L) and washers again onto the blade
• Slide blades to allow file clearance using slots (M) on bottom of blade. Do not pry against
cutting edges.
• File each edge carefully. Follow the original shape of the blade.
Important: If a power grinder is used do not allow blade to over heat.
• Install blade stiffener in reverse order.
Note: Use new locknuts every time blade stiffener is installed.
• Lubricate blades (see “Lubrication instructions”).
GB
10 Gardenline
* Do not use fuel containing methyl alcohol, more than10% ethyl alcohol or 15% MTBE.
Package contents
After opening the carton, check for damage. Immediately notify your retailer or the address on
the warranty card of damaged or missing parts. Use the contents list to check for missing parts:
1
Hedge trimmer
1 T-Wrench 17 x 19
1 Spanner S8 - S10
1 Fuel - oil mixing bottle
1 Instruction manual
1 Safety instructions
1 Warranty card
Description
Fig. 1
There are the safety decals on your hedge trimmer. Make sure the decals are legible and that
you understand and follow the instructions on them.
1. Front handle guard
Comfortable, textured finish provides anti-slip grip for front hand. Guard protects hand
from the blades. Warning decals are located on guard.
2. Blades
Double reciprocating blades mounted to a blade support bar. The blades are double sided,
capable of cutting on either side.
3. Blade stiffener
Attaches to top of blades and guides material being cut into blades.
4. Spark plug
Provides spark to ignite fuel mixture.
5. Choke
The choke control lever is located on the front of the air cleaner case. Move choke lever to
"Cold start" position to close the choke for Cold Starting. Move choke lever to "Run"
position to open choke.
6. Primer bulb
Pumping primer bulb before starting engine draws fresh fuel from the fuel tank priming the
carburetor for starting. Pump primer bulb until fuel is visible and flows freely in the clear fuel
tank return line. Pump bulb an additional 4 or 5 times.
Fuel tank capacity 0.6 L (20.3 fl. oz)
Starter system Automatic recoil starter
Clutch Centrifugal type
Gear case ratio 58:14
Cutter Double reciprocating blade, double edge
Blade length 600 mm (24”)
Teeth pitch 27 mm (1.06”)
Max. cutting diameter 10 mm (0.4”) (soft wood)
Dry weight 5.6 kg (12.3 lb.)
GB