Gardena Flymo 1200R Скачать руководство пользователя

Страница: 43 / 48

7 Transportation, storage and disposal

7.1 Transportation

The contained lithium-ion-batteries are subject to the

Dangerous Goods Legislation requirements. For

commercial transports e.g. by third parties or forwarding

agents, special requirement on packaging and labeling

must be observed. Consult an expert for hazardous

material for preparation of the item being shipped.

Please also observe possibly more detailed national

regulations.
Tape off open contacts and pack up the battery in such

a manner that it cannot move around in the packaging.

Always secure the product when transporting it.

7.2 Winter storage

7.2.1 The robotic lawnmower

The robotic lawnmower must be cleaned carefully before

putting it away for the winter. See

Clean the robotic

lawnmower on page 33.
To guarantee battery functionality and service life, it is

important to charge the robotic lawnmower before

storing it away for the winter. Place the robotic

lawnmower in the charging station with the hatch open

until the battery icon in the display shows that the

battery is fully charged. Then set the main switch to

Check the condition of wear items such as blades and

bearings in the rear wheel. Rectify if necessary to make

sure the robotic lawnmower is in good condition prior to

next season.
Store the robotic lawnmower standing on all wheels and

place it in a dry, frost-free environment, preferably in the

mower’s original packaging. You can also hang the

robotic lawnmower on a Flymo original wall hanger.

Contact your local Flymo representative for more

information about available wall hangers.

CAUTION: The battery must be charged fully

before winter storage. If the battery is not fully

charged it can be damaged and in certain cases

be rendered useless.

7.2.2 The charging station

Store the charging station and power supply indoors.

The boundary wire and the guide wire can be left in the

ground.
1. Disconnect the charging station power supply.
2. Release the connector lock and pull the connector

out.

3. Disconnect the boundary and guide wire contacts

from the charging station.

The ends of the wires should be protected from damp by

putting them in a container with grease for instance.

CAUTION: If it is not possible to store the

charging station indoors, the charging station

must be connected to the mains, the boundary

wire and the guide wires the entire winter.

7.3 After winter storage

Check if cleaning is needed, particularly the charging

strips on both the robotic lawnmower and the charging

station. If the charging strips appear to be burnt or

coated, clean them using a fine grade emery cloth.

Check also that the robotic lawnmower's time and date

are correct.

7.4 Environmental information

The symbol on the Flymo robotic

lawnmower indicates that this product

cannot be treated as domestic waste. It

should instead be left at a suitable

recycling centre to recycle its electronic

components and batteries. The battery

must be removed from the product before

it is scrapped.

By ensuring that this product is taken care of correctly,

you can help to counteract the potential negative impact

on the environment and people that can otherwise result

through incorrect waste management of this product.
For more detailed information about recycling this

product, contact your municipality, your domestic waste

service or the shop from where you purchased the

product.

7.5 Removal of battery for recycling

For removal the battery from the robotic lawnmower see

Battery on page 34.

365 - 001 -

Transportation, storage and disposal - 43

Содержание Flymo 1200R

















































Результаты поиска

Содержание Flymo 1200R

Отзывы:

Похожие инструкции для Flymo 1200R

Бренды по названию

Популярные бренды

Gardena Flymo 1200R, Руководство оператора

Результаты поиска

Содержание Flymo 1200R

Отзывы:

Похожие инструкции для Flymo 1200R

Бренды по названию

Популярные бренды