background image

5.

Stage   2   -   Installation Procedure Modules & Delivery Pipe Assys

Continues

(Start with Module A closest to Column)  (Refer Pg. 16 or 17)

 

Install Module Assy. fit Hinge Pin lift module & Position Hold Up Brace (Refer pg. 9)

 

Attach Feed Line & Delivery Lines to Meter Module

(Ensure Correct Feed Path - See Drawing Provided Pg. 16 or 17)

 

Repeat previous procedure for the B Module then the C Module

 

Connect Mains & Switched Phase Cables into AC Control Boxes (see Drawing Pg. 31)

(Inspection required)

 

 Using Draw Cord Pull Encoder, Float Switch  & AC Signal Cables through Cable

Duct roll up & secure surplus cable

 

Plug Cables into Logic PCB  (see Drawing Pg. 32)  Cables are Marked

 

Fit Steel Wire Armoured Cable Mains Feed Line to Head Cabinet (Gland FLP.)

connect as per Drawing  Pg. 31 (inspection required)  (Gland not Supplied)

 

Insert Data Cable into Head Cabinet via Gland

 

Insert Pump & LAN Comm’s Cable into Head Cabinet & Connect

Pump Comms Refer Pg. 29 & 31   LAN Comms. Direct to FST unit (Plug Supplied)

 

Install Earth Bonding Cable between Column & Head Cabinet

 

Attach Nozzle Holster Switch Cables to Logic Box (see Drawing Pg. 32) + pg.16 & 17

 

Check all Hydraulic & Electrical connections ( Electricals to be Certified)

 

Program Dispenser as per pages 13-18- (Also refer PEC Modular Pumps Manual

87372

 

Test run checking for leaks etc.

 

Check Cover is replaced over Power Supply PCB.

Содержание Apollo 3000


















































































Отзывы: