7
SECTION
FITTING THE COVER INTO
POSITION
1.
Turn the flow control knob spindle anti-
clockwise until the valve is fully open,
before switching on the unit (
See Fig 1
).
This will ensure a fast fill up of the unit
when the shower is first switched ‘ON’.
IMPORTANT!
THE SHOWER MUST BE FULL OF
WATER BEFORE HEAT SETTINGS ARE
USED.
Secure the cover with the two fixing
screws provided.
Switch on the power to the shower unit at
the consumer unit and the double pole
switch. At this stage the power selector
knob should be on the
COLD
position
(Solid Blue Symbol)
.
Remove the shower head from the flexible
hose and point to waste.
I
I
I
I
Connect the live cable to the terminal
marked
L
.
Connect the neutral cable to the terminal
marked
N
.
Connect the earth cable to the terminal
marked
E
on the back plate.
IMPORTANT
Ensure that the terminal block screws are
fully tightened and that no cable insulation
is trapped under screws,
Ensure the cable clamp is used to secure
the cable.
The earth continuity conductor of the
electrical installation must be effectively
connected to all exposed metal parts of
other appliances and services in the room
in which the shower unit is installed to
confirm with IEE regulations.
I
I
I
I
FLOW
SPINDLE
1
2
Start the shower unit by press the
START/
STOP
button. Let the water flow through
the shower unit to release any air which
may be in the system and fill the shower
unit with water.
2.
It may be necessary to reposition the
flow control knob in the cover. This can
be done by turning the flow control knob
clockwise, on the full power setting until
you get a nice warm shower (
See Fig 1
).
Let the shower run for a short time then
switch the shower unit OFF by pressing
the
START/STOP
button. Also switch
OFF the power and pull cord switch.
Remove the cover and reposition the
flow control knob in the roughly an
8 o’clock position. Refit the cover.
I
HOT
COLD
Fig 2
Fig 1
You should now be able to get a HOT
shower with the knob positioned at
about 11 o’clock and a COLD shower
with the knob positioned at about
1 o’clock by turning the flow control
knob anti-clockwise (
See Fig 2
).
Re-fit the shower head to the flexible hose.
Your shower is now ready to use. We
recommend that you allow your shower to
reach a stable temperature before you
commence showering.
I
I
8
SECTION
RISER RAIL & SOAP DISH
FITTING INSTRUCTIONS
TIPS
A piece of insulating or masking tape
applied to the wall before marking out the
fixing holes will help stop the drill from
wandering, particularly on tiled surfaces.
When working near a basin or bath, insert
the plug in the waste fitting so that small
parts cannot be lost. Take care not to drop
accessories or tools into basin or bath.
CAUTION
Check there are no hidden cables or pipes
before drilling holes for wall plugs. Exercise
great care when using power tools near
water. The use of a residual current device
(RCD) is recommended.
1.
Establish position for the
riser rail, and mark the wall for
the
lower
mounting bracket.
Make allowances for the tallest
person likely to use the shower
regularly.
2.
Use a No 10/5.5mm masonry
drill to make a hole 35mm deep,
and fit the wall plug.
(NB some
wall constructions may require the
use of alternative types of wall
fixings)
.
Screw the lower bracket
base to the wall.
4.
The crimped end of the riser
rail.
NOTE If it is necessary to
shorten the rail, use a junior
hacksaw to cut the excess material
from the plain end of the rail.
3.
Locate the crimped end of
the riser rail (Figure 4) into the
mounting bracket, then fit the
upper bracket. Ensure the rail is
vertical, then mark the wall for
the fixing.
5.
The three components that
comprise the Handset Height
Adjuster assembly are produced
with alphabetical ‘A’s and ‘B’s
moulded into the end section of
each part. Simply just match the
letter identification of each part with the central
piece i.e. ‘A’ to ‘A’ and ‘B’ to ‘B’ for correct
assembly.
6.
With the showerhead height
adjuster lever set a 3 o’clock
and the showerhead holder in
the upright position, slide the
assembly onto the rail. Tighten
to the rail by turning the lever.
7.
To lock the Handset Height
Adjuster at your chosen position
on the rail. Turn the lever up
right. This action is also used for
holding the showerhead at the
angle required.
8.
Re-assemble the rail and
screw the upper mounting
bracket in place.
9.
Slide the end cap onto the
mounting brackets.
10.
Snap the soap dish onto the
rail below the holder assembly.
