background image

2X3 BAND TUBE EQUALIZER 

!

OPERATION AND SAFETY PRECAUTIONS 

Please note that the GLA-PEQ EMPRESS is intended for professional use. It’s not a 
consumer  electronic  device. 

Its  installation  and  use  require  certain  professional 

sound  engineering  knowledge  and  skills.  Lack  of  this  knowledge  may  result  in 
malfunction, damage or personal injury. 

 

Use only grounded electrical outlet!

Do not open the device and don’t do any modi

cations on it!

Do  not  attempt  to  repair  or  replace  any  of  the  components  unless
speci

cally instructed to do so in this guide.

Pay attention to not put any solid matter (

ammable things, coin, nail etc)

or liquid (water, alcohol etc.) inside device.

Do not twist or break the power cord or place heavy objects on it. Doing
so may damage the cable and cause a short circuit. Damaged cables can
cause 

re and electric shock!

Protect  the  device  from  intesive  external  shock!  (for  example:  falling
down)

Never use the device in following conditions:

-

Extreme temperature

-

Moisture

-

High humidity

-

Rain

-

Dust

-

Heavy vibration

In  the  following  cases,  turn  o

  the  machine  immediately,  unplug  the 

power cord, and contact us (www.gainlabaudio.com):  

if the mains plug of the appliance is damaged

!

!

1

Содержание EMPRESS GL-PEQ














Отзывы: