background image

 

P

UB 

42004-438A 

 

300

 

S

ERIES 

E

MERGENCY 

T

ELEPHONE 

M

ANUAL

 

P

AGE 

21 of 44

 

f:\standard ioms - current release\42004 instr. manuals\42004-438a.doc 
02/11

 

Setup 

Hardware Configuration 

The hardware configuration options are explained in detail in the following sections, and the necessary 
jumper settings are identified to enable or disable each option.  Reading each section and recording the 
selected options prior to making the necessary changes is recommended.  Create a record of your settings 
using Table 3 on page 22.  See Figure 23 on page 23 for the jumper locations. 

Auto-answer Configuration 

Factory Setting

:  Auto-answer feature enabled 

The Auto-answer feature enables or disables the automatic answering of an incoming call, which allows 
TMA to monitor the health of this phone via polling.  When the Auto-answer feature is enabled, the 
phone automatically answers the call and attempts to communicate with TMA.  If the caller is not TMA, 
the telephone automatically transitions to a standard two-way communication. 

Enable

: J14 jumper on pins 2 and 3. 

Disable

: J14 jumper on pins 1 and 2 (Do not use this setting except under the direction of GAI-Tronics 

personnel.) 

N

OTE

:

  The Auto-answer feature must be enabled during remote programming, and to allow the 

GAI-Tronics Telephone Management Application PC to contact the phone. 

Polarity Configuration 

Factory Setting

: Non-polarity sensitive 

This telephone can be configured to be polarity or non-polarity sensitive.  With the non-polarized setting, 
the telephone operates regardless of tip and ring polarity.  With the polarized setting, the telephone only 
operates with the telephone line’s positive terminal connected to the tip.  Use the Polarity Sensitive 
setting to allow a line voltage reversal disconnect signal to disconnect the call. 

Non-polarity Sensitive

: J6 jumper on pins 2 and 3. 

Polarity Sensitive

: J6 jumper on pins 1 and 2. 

DTMF Gain Select Configuration 

Factory Setting

: Low Gain selected. 

Two gain selections are available in the DTMF detection circuit.  In most installations, the low gain 
setting is recommended. 

Low Gain Selected

: J17 jumper on pins 1 and 2. 

High Gain Selected

: J17 jumper on pins 2 and 3. 

Содержание Redalert 392-001
















































Отзывы: