background image

13

 

7/21 REV 5/22

 

 

 

GB745SHAVT INSTALLATION TOOL

 

If a tool is performing poorly or leaking, a complete overhaul may be necessary.

 

 

Perform overhaul in a clean, well lit area using care not to scratch or nick any smooth surface that comes in contact with an o'ring. 

Use of Lubriplate® #630

-

AA (Gage Bilt part no. 402723) or equivalent during reassembly to prevent tearing or distorting of o'rings.

 

 

1.  Disconnect air supply. 

 

 

2.  Disconnect hydraulic coupler

-

male (585047) from power supply and air line (704311) from pump. 

 

 

3. Remove hydraulic coupler

-

male (585047) from reducer bushing (403431) and drain hydraulic hose (A

-

317) into an approved 

 

container.

 

 

4.  Remove complete nose assembly and extensions (if applicable) from tool. 

 

 

5.  Remove four button head cap screws (402489) separating handle assembly (700344) from head cylinder (745366).

 

 

6.  Replace o

ring (S832) and gasket (745124). 

 

 

7.  Remove end cap assembly (748118) and carefully push piston (745310) out of head cylinder (745366). 

 

 

   

8.  Using a small blunt object, remove back

-

up rings (401119) and o

ring (403815) from piston (745310) and o

ring (A

-

261) and 

   

 

back

-

up ring (401092) from inside head cylinder (745366).

 

 

9.  Reassembly sequence is opposite of disassembly. Be sure relative positions of o'rings and back

-

up rings are as shown in 

 

 

exploded view and part list. 

 

 

Coat hose fitting threads with a non

-

hardening Teflon® thread compound such as Slic

-

tite® (Gage Bilt part no. 403237). DO NOT USE 

TEFLON TAPE.

 

OVERHAUL

 

TOOL DISPOSAL

 

1.

 

When tool life is met, drain hydraulic oil from tool and dispose of the hydraulic oil in accordance with the safety datasheet.

 

  

 

2.

 

Disassemble tool and remove all rubber o

rings, seals, wipers and hydraulic hoses. All tool materials are recyclable except rubber 

o

rings, seals, wipers and hydraulic hoses. Dispose of rubber materials in accordance with the material safety datasheet. 

 

 

WARNING

:  

Only qualified and trained personnel shall perform overhaul. 

 

 

WARNING

:  

Personnel must read and understand all warnings and cautions. 

 

 

WARNING

:  

Tool must be maintained in a safe working condition at all times and examined on a daily basis for damage or 

 

wear. Any repair must be done by qualified personnel trained on Gage Bilt procedures.

 

 

WARNING

:  

Disconnect tool from its power source before performing overhaul. Severe personal injury may occur if power 

 

source is not disconnected.

 

 

 

 

WARNING

:  

Excessive contact with hydraulic oil and lubricants must be avoided (See safety data sheet documents for all 

 

 

applicable materials).

 

 

           

WARNING

:  

When operating, repairing or overhauling tool, wear approved eye protection. Do not look in front of tool or 

 

rear of tool when installing fastener. 

 

 

 

 

WARNING: 

 

Use only Gage Bilt hydraulic hoses and couplings, or equivalent, rated for 10,000 psi. (689.5 bar) working pressure.

 

 

 

WARNING: 

 

Ensure air hose is securely connected to avoid possible hose whipping (Air Actuated Tools only).

 

 

WARNING:  

Depress lever (704345) and disconnect from air, with the piston in the rear position, before overhaul. Severe personal 

 

injury may occur if air hose is not disconnected. 

USE CAUTION

 when forcing piston rod assembly downward with 

 

head cylinder removed. Hydraulic oil will eject forcibly from handle assembly.

 

 

Note: 

 

 

• 

Dispose of hydraulic oil in accordance with manufacture safety datasheet.

 

• 

All tool materials are recyclable except rubber o

rings, seals and wipers.

 

• 

Use of SERVICE KIT (745020), which contains a complete set of o'rings, back

-

up rings, screws, washers and 

gasket, can achieve a complete overhaul.

 

Содержание GB745SHAVT





















Отзывы: