background image

8

 

REV 5/22

 

 

 

GB745/206

-

500  S/N:1329  AND ABOVE 

 

PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

 

HOW TO SET

-

UP THE GB745/206

-

500

 

RED SHIPPING PLUG

 

CYLINDER

 

ACTUATOR

 

Image may not reflect actual tool

 

WORK

 

FASTENER

 

 

The tool is shipped with a red plastic plug in the air inlet connector. The connector has a 1/4

-

18 female pipe thread to accept user air 

hose fitting. The tool comes with oil and is ready to use.

 

 

   

1.  Remove red plastic shipping plug from Swivel (A

-

249) (air inlet) and screw in your quick disconnect (air) fitting.

 

 

 

 

   2.  Connect tool to air hose with 90 psi. (6.2 bar) using clean, dry air. 

3/8” (9.52 

mm) minimum diameter air line is recommended.  

 

 Cycle tool five times by depressing and releasing actuator assembly

-

air (704130).

 

 

   3.  Disconnect air hose from tool.

 

 

   4.

  

Select proper nose assembly (See nose assembly selection chart on pg. 19 for more information). Screw drawbar into piston on 

tool and secure using hex key on front of drawbar. (See proper data sheet for further instructions).

 

.

 

   5.

  

Connect air supply.

 

AIR HOSE

 

USER QUICK

 

DISCONNECT FITTING

 

AIR INLET 

 

WARNING:

 

Only qualified and trained operators must install, adjust or use the assembly power tool for non

-

threaded 

 

 

 

 

       mechanical fasteners. 

 

 

WARNING: 

Operator 

MUST 

read and understand all warnings and cautions.

 

 

WARNING: 

It is required that eye protection, hearing protection and safety boots be worn at all times while handling this 

equipment.

 

 

WARNING: 

The users or the user

s employer must assess specific risks that could be present  as a result after each use 

 

 

        based on their application. 

 

 

 

●  

Ensure there is adequate clearance for tool and operator's hands before proceeding. Keep fingers clear of any 

 

 

 

moving parts. Keep fingers clear from fasteners and installed materials. Severe personal injury may result.

 

 

 

 

●  

Verify 

the air lines and/or hydraulic hoses are not a trip hazard.

 

 

 

 

●  

Ensure that there are no electrical cables, gas pipes, etc., which can cause a hazard if damaged by the tool

 

 

 

WARNING: 

Do not actuate fastener in the air. Personal injury from fastener ejecting may occur.

 

 

WARNING: 

Air is exhausted from the bottom of the tool. Direct bottom of the tool (exhausted air) away from operator, other   

 

 

 persons working in the vicinity, foreign matter and liquid.

 

 

WARNING: 

Do not carry from hoses or use as a hammer.

 

 

 

 

WARNING: 

Do not use in explosive atmosphere.

 

 

WARNING: 

Ensure air hose is securely connected to avoid possible hose whipping.

 

 

WARNING: 

Always disconnect air supply when tool is not in use to prevent accidental start

-

up.

 

 

WARNING: 

Ensure there is adequate clearance for tool and operator hands.

 

 

WARNING: 

Do not operate this tool without deflector, pintail catcher bag or pintail collection bottle in place.

 

 

CAUTION: 

 

Do not use beyond the design intent.

 

NOSE ASSEMBLY

 

Содержание GB745/204

























Отзывы: