background image

15

 

Rev. 1/23

 

 

GB713SR

-

8 INSTALLATION TOOL 

S/N: 1024 AND ABOVE 

 

PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

 

OVERHAUL

 

REMOVING ACTUATOR ASSEMBLY

-

AIR (704130)

 

 

 

1.

 

Remove lever assembly (724017) including pin.

 

 

2.

 

With lever assembly (724017) removed, insert a 

5/8” 

open end box wrench / adjustable wrench around actuator 

assembly

-

air (704130).

 

 

3.

 

Loosen the actuator assembly

-

air (704130).

 

 

4.    Remove wrench. Unthread and remove the actuator assembly

-

air (704130) with fingers from the 

 

manifold head 

 

assembly (744306). 

 

INSTALLING ACTUATOR ASSEMBLY

-

AIR (704130)

 

 

 

1.

 

Apply Teflon® tape onto threads of actuator assembly

-

air (704130) one to two wraps.

 

 

2.

 

Thread the actuator assembly

-

air (704130) all the way into manifold head assembly (744306) with fingers.

 

 

3.

 

Insert and turn 

5/8” 

open end box wrench / adjustable wrench and snug tight approximately 1/4

-

1/2 turn.

 

 

4.

 

Re

-

attach the lever assembly (724017) with pin.

 

Image may 

not reflect 

actual tool.

 

ACTUATOR ASSEMBLY

-

AIR

 

 

WARNING

Disconnect tool from its power source before actuator removal or installation. Severe personal injury may occur if 

 

power source is not disconnected.

 

 

 

CAUTION:  

Actuator assembly

-

air (704130) can break if not careful.

 

 

CAUTION:  

Do not over tighten actuator assembly

-

air (704130). Snug tighten only.

 

Содержание GB713SR-8

























Отзывы: