background image

 

7/11 REV 10/14 

 

PRINCIPLE OF OPERATION 

 

When the air actuator assy is depressed, the pressurized air inside of the tool is released allowing spring pressure to move  the 
valve spool assy causing the air to be redirected. The air is directed to the top of the air piston assy, moving it in a downward di-
rection. The air below the air piston assy is then directed through the valve sleeve and exhausted out of the bottom of the tool. 
Simultaneously, the piston rod assy connected to the air piston assy is also moving down, forcing hydraulic oil up and into the 
front side of the head cylinder assy, causing the piston to move to the rear of the head cylinder assy. The internal components of 
the  attached  nose  assembly  are  also  moving with  the piston  to start  the  fastener installation.   When  the  fastener  installation  is 
completed, the air actuator assy is released. Air pressure is then built up inside of the handle assy causing the valve spool assy to 
return to its original position and reversing the sequence directing air pressure to the rear of the head cylinder assy, causing the 
piston to move to the forward position. 

 

Image may not reflect actual tool 

Содержание GB713















Отзывы: