Gage Bilt GB703SR8VT Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 15

background image

REV. 10/14

2

SPECIFICATIONS

Hand Held Weight

- 1.5 lbs. (.68 kg)

Air pressure req'd

- 90-100 psi. (6.2-6.9 bar)

Air consumption

- .29 SCF/cycle (8.21 L/cycle)

Hydraulic oil

- Automatic Transmission Oil,

Dexron® III, or equivalent.

Setting stroke

- .800" (20.32 mm)

Noise level

- Less than 81.5 dB (A)²

Rated pull load

- 2,200 lbs.

(9.79 kN)

Vibration

- Tested– No Hazards Found

TABLE OF CONTENTS

Description

Page

Warnings ............................................................................................................................................. 3

Principle of Operation ......................................................................................................................... 4

How to use the GB703SR8VT .............................................................................................................. 5

Description, Maintenance and Hydraulic Thread Preparation ......................................................... 6

Filling & Bleeding ................................................................................................................................ 7

Troubleshooting .................................................................................................................................. 8

Overhaul ............................................................................................................................................... 9

Disassembly and Parts List ........................................................................................................ 10-11

DEXRON® III Oil Safety Data ............................................................................................................. 12

Nose Assembly Selection Chart .................................................................................................. 13-14

EU Conformity and Warranty ............................................................................................................ 15

4.25

(108mm)

8.00

(203.2mm)

4.44

(112.8mm)

1.87

(47.5mm)

1.15

(29.3mm)

.87 Ø

(22.1mm)

«
1
2
3
4
...
»

Содержание GB703SR8VT
















Отзывы:

Нет отзывов

Похожие инструкции для GB703SR8VT

Бренд: Lambda Страницы: 25

Бренд: Gallagher Страницы: 96

Бренд: Dake Страницы: 17

Бренд: Jet Страницы: 12

Бренд: PELA Страницы: 8

Бренд: jbc Страницы: 4

Бренд: OBO Bettermann Страницы: 2

Бренд: Bench Dog Tools Страницы: 12

Бренд: Ferm Страницы: 96

Бренд: Wacker Neuson Страницы: 22

Бренд: Harrington Страницы: 2

Бренд: LEYBOLD Страницы: 3

Бренд: Panduit Страницы: 2

Бренд: Xantrex Страницы: 76

Бренд: Yardworks Страницы: 19

Бренд: Hakko Electronics Страницы: 8

Бренд: Corsair Страницы: 42

Бренд: National Instruments Страницы: 47

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды