background image

 

G-Tek Corporation Private Limited 

13 

 

5.1.1.2

 

Sensor Wiring 

To  ensure  maximum  LmNet  performance,  proper  wiring  installation  practices  must  be  followed. 
Failure to do so can result in a range of problems, from loss of configuration to component failure, 
caused by transmitted or radiated electrical noise. Proper consideration must be given to local noise 
sources and appropriate suppression steps taken to minimize any potential problems. 

Among the most common sources of noise are: Relays, SCRs, valve solenoids, electric motors, power 
line disturbance, wire-to-wire coupling, electrostatic discharge (ESD) and radio-frequency interference 
(RFI). 

1.

 

To achieve the best results, the following notes should be considered: 
Low  level  signal  wiring  such  as  that  associated  with  thermocouples,  RTDs  and  current  loops 
should always be kept separate from power and control output wiring. 

 

2.

 

Signal input wiring should be twisted pairs/triplets etc. and the conductors should be stranded 
rather than solid in construction. All signal wiring should use ground-shielded wires or be routed 
through grounded conduit. This minimizes the effects of RFI and ESD. 

 

3.

 

Special  care  should  be  taken  when  wiring  to  relay  or  solenoid  coils,  as  large  transients  are 
produced  when  coils  (or  any  other  inductive  devices)  are  switched.  This  problem  can  be 
eliminated  using  suitable  suppression  devices  across  the  coil.  Coil  transients  can  also  be 
transmitted through the  air, so the recorder itself should be mounted as far as possible from 
power control devices and/or wiring. 

 

4.

 

When  line  power  is  poorly  regulated  and  /  or  subject  to  voltage  surges  or  transients, 
consideration should be given to the use of a line conditioning/transient suppressing line power 
regulator. Process control motors, valves,  relays,  and heaters should not be connected to the 
same power lines that are used for instrumentation. 

 

5.

 

The connection of the LmNet to a proper safety earth ground is essential. Such a connection not 
only reduces the possibility of electric shock, but also provides the required return for the LmNet 
line power filters. 

 

6.

 

All local electrical codes of practice must be followed when installing any instrumentation. For 
sensor wiring, all the sensor connectors are at the back side of the LmNet as shown in figure 9. 

 
 
 
 

Содержание LmNet - PRO 614-00






















































Отзывы: