background image

-

19

-

13. Specifications                      

14. Warranty and service          

Operating voltage range:                      10.0~18.0Volt
Circuit power:                                        max.150W for charging
                                                              max.25W for discharging                                
Charge current range:                           0.1~7.0A
Discharge current range:                       0.1~5.0A
Current drain for balancing Li-po:          300mAh/cell
NiCd/ NiMH battery cell count:              1~27cells
Lithium battery cell count:                      1~8Series
Pb battery voltage:                                 2 to 36V
Weight:                                                   700g
Dimension:                                            165×130×45mm

We warrant this product for a period of one year(12 months) from the date of 

purchase. The guarantee applies only to such material or operational defects, which 
are present at the time of purchasing the product. During that period, we will replace 
without service charge any product deemed defective due to those causes. You will 
be required to present proof of purchase (invoice or receipt). This warranty does 
not cover the damage due to wear, overloading, incompetetent handling or using of 
incorrect accessories.

 Note:

Содержание A8
























Отзывы: