background image

Heat day

= Heater temperature by day time

Heatnight

= Heater temperature by night time

Hyst.

= Hysteresis setting

Select e.g: "Heat day" here you can adjust the temperature on the day time. Proceed as 
usual, pressing ENTER the value starts to blink, change the value with UP / DOWN 
buttons, you can store the value with SAVE / EXIT. Go to the next setting "Heatnight" and 
repeat the procedure.

The hysteresis determines the quiescent condition of the contact. e.g: If the hysteresis is 
set to -2.0°C and a set value to 24.0°C, then the heater will at 24.0°C - 2.0°C = 22.0°C and
among switch on and reaching the value of 24.0°C switch off again. This contact will 
remain off until the value again drops below 22.0°C.

Output sensor 1 cool:

The procedure is the same as in "Output Sensor 1 heat" only the hysteresis works in 
reverse mode during the cooling. e.g: If the hysteresis is set to + 2.0°C and a set value is 
24.0°C, the cooling capacity becomes 24.0°C + 2.0°C = 26.0°C and by reaching 24.0 °C is
off again. This contact will remain off until the value rises above 26.0°C.

Output sensor 1 humidify/moisturise:

The procedure is the same as before. When connecting a humidifier, choose the relative 
humidity = rH in % at day and at night time and set the desired hysteresis.

Output sensor 1 dehumidify/drying; Output sensor 2 heat; Output 

sensor 2 cool:

The procedure is repeated for all other outputs as previously.

Output 1 timer:

If you choose the timer function it allows you to enter the start and end time in 24 day 
cycles. Start time in hours and minutes, end time in hours, minutes and seconds. There 
are 25 cycles per output programmable.

Select the "Ex = timer" Exit 1 timer 1. The first five character 

00:00

 represents the on-time 

in hours and minutes from 00:00 to 23:59. The next eight character 

00:00:00

 stand for off-

time in hours, minutes and seconds from 00:00:00 to 23:59:59 in 24hour format.

page 11 of 15

Exit 1  timer 01

Exit 1  timer 02

Exit 1  timer 03

00:00   00:00:00

00:00   00:00:00

end     disabled

h h : m m

h h : m m  :  s s

Содержание 16A
















Отзывы: