background image

 

 

8

General Troubleshooting 

 
This Chapter provides information on diagnosing and solving operational problems.  
If a solution to your problem cannot be found in the following subsections, contact 
your authorized dealer or G-Lites Technical Support. 
 
Unit functions but lamp does not strike: 

o

 

Make sure the correct lamp has been installed in the fixture. 

o

 

Check for loose igniter or power supply connection. 

o

 

Replace lamp. 

o

 

If lamp is still hot from recent operation, leave the unit turned on and when the 
lamp’s temperature drops, it will restrike. 

 
Unit is producing unexpected results 

o

 

Check DMX starting address on the fixture and console match. 

o

 

Verify that the last fixture on the link is terminated. 

 
Unit is not responding to console: 

o

 

Verify that the fixture has the correct DMX address 

o

 

Check and replace data cables 

o

 

Verify that the last fixture on the link is terminated. 

 

Unit is not moving 

o

 

Check if the power supply is suitable for the voltage of the fixture. 

o

 

Replace sensors. 

o

 

Please check if the inside lead wire and the connector are loose. 

o

 

Please check the electric part (such as the switch, transformer, ballast, electric 
capacity, resistor, filter, PCB board, controller to motor). 

 

Pan or Tilt position is off: 

o

 

Verify that all belts are tight. 

o

 

Home the fixture. 

 

Содержание STAR SEARCH 4000









Отзывы: